/* $NetBSD: siireg.h,v 1.2 2006/07/29 19:10:57 ad Exp $ */ /* * Copyright (c) 1992, 1993 * The Regents of the University of California. All rights reserved. * * This code is derived from software contributed to Berkeley by * Ralph Campbell. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * 3. Neither the name of the University nor the names of its contributors * may be used to endorse or promote products derived from this software * without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ``AS IS'' AND * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE * ARE DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF * SUCH DAMAGE. * * @(#)siireg.h 8.1 (Berkeley) 6/10/93 * * sii.h -- * * SII registers. * * Copyright (C) 1989 Digital Equipment Corporation. * Permission to use, copy, modify, and distribute this software and * its documentation for any purpose and without fee is hereby granted, * provided that the above copyright notice appears in all copies. * Digital Equipment Corporation makes no representations about the * suitability of this software for any purpose. It is provided "as is" * without express or implied warranty. * * from: Header: /sprite/src/kernel/dev/ds3100.md/RCS/sii.h, * v 1.2 89/08/15 19:53:04 rab Exp SPRITE (DECWRL) */ #ifndef _SII #define _SII /* * SII hardware registers */ typedef volatile struct { u_short sdb; /* SCSI Data Bus and Parity */ u_short pad0; u_short sc1; /* SCSI Control Signals One */ u_short pad1; u_short sc2; /* SCSI Control Signals Two */ u_short pad2; u_short csr; /* Control/Status register */ u_short pad3; u_short id; /* Bus ID register */ u_short pad4; u_short slcsr; /* Select Control and Status Register */ u_short pad5; u_short destat; /* Selection Detector Status Register */ u_short pad6; u_short dstmo; /* DSSI Timeout Register */ u_short pad7; u_short data; /* Data Register */ u_short pad8; u_short dmctrl; /* DMA Control Register */ u_short pad9; u_short dmlotc; /* DMA Length of Transfer Counter */ u_short pad10; u_short dmaddrl; /* DMA Address Register Low */ u_short pad11; u_short dmaddrh; /* DMA Address Register High */ u_short pad12; u_short dmabyte; /* DMA Initial Byte Register */ u_short pad13; u_short stlp; /* DSSI Short Target List Pointer */ u_short pad14; u_short ltlp; /* DSSI Long Target List Pointer */ u_short pad15; u_short ilp; /* DSSI Initiator List Pointer */ u_short pad16; u_short dsctrl; /* DSSI Control Register */ u_short pad17; u_short cstat; /* Connection Status Register */ u_short pad18; u_short dstat; /* Data Transfer Status Register */ u_short pad19; u_short comm; /* Command Register */ u_short pad20; u_short dictrl; /* Diagnostic Control Register */ u_short pad21; u_short clock; /* Diagnostic Clock Register */ u_short pad22; u_short bhdiag; /* Bus Handler Diagnostic Register */ u_short pad23; u_short sidiag; /* SCSI IO Diagnostic Register */ u_short pad24; u_short dmdiag; /* Data Mover Diagnostic Register */ u_short pad25; u_short mcdiag; /* Main Control Diagnostic Register */ u_short pad26; } SIIRegs; /* * SC1 - SCSI Control Signals One */ #define SII_SC1_MSK 0x1ff /* All possible signals on the bus */ #define SII_SC1_SEL 0x80 /* SCSI SEL signal active on bus */ #define SII_SC1_ATN 0x08 /* SCSI ATN signal active on bus */ /* * SC2 - SCSI Control Signals Two */ #define SII_SC2_IGS 0x8 /* SCSI drivers for initiator mode */ /* * CSR - Control/Status Register */ #define SII_HPM 0x10 /* SII in on an arbitrated SCSI bus */ #define SII_RSE 0x08 /* 1 = respond to reselections */ #define SII_SLE 0x04 /* 1 = respond to selections */ #define SII_PCE 0x02 /* 1 = report parity errors */ #define SII_IE 0x01 /* 1 = enable interrupts */ /* * ID - Bus ID Register */ #define SII_ID_IO 0x8000 /* I/O */ /* * DESTAT - Selection Detector Status Register */ #define SII_IDMSK 0x7 /* ID of target reselected the SII */ /* * DMCTRL - DMA Control Register */ #define SII_ASYNC 0x00 /* REQ/ACK Offset for async mode */ #define SII_SYNC 0x03 /* REQ/ACK Offset for sync mode */ /* * DMLOTC - DMA Length Of Transfer Counter */ #define SII_TCMSK 0x1fff /* transfer count mask */ /* * CSTAT - Connection Status Register */ #define SII_CI 0x8000 /* composite interrupt bit for CSTAT */ #define SII_DI 0x4000 /* composite interrupt bit for DSTAT */ #define SII_RST 0x2000 /* 1 if reset is asserted on SCSI bus */ #define SII_BER 0x1000 /* Bus error */ #define SII_OBC 0x0800 /* Out_en Bit Cleared (DSSI mode) */ #define SII_TZ 0x0400 /* Target pointer Zero (STLP or LTLP is zero) */ #define SII_BUF 0x0200 /* Buffer service - outbound pkt to non-DSSI */ #define SII_LDN 0x0100 /* List element Done */ #define SII_SCH 0x0080 /* State Change */ #define SII_CON 0x0040 /* SII is Connected to another device */ #define SII_DST 0x0020 /* SII was Destination of current transfer */ #define SII_TGT 0x0010 /* SII is operating as a Target */ #define SII_STATE_MSK 0x0070 /* State Mask */ #define SII_SWA 0x0008 /* Selected With Attention */ #define SII_SIP 0x0004 /* Selection In Progress */ #define SII_LST 0x0002 /* Lost arbitration */ /* * DSTAT - Data Transfer Status Register */ #define SII_DNE 0x2000 /* DMA transfer Done */ #define SII_TCZ 0x1000 /* Transfer Count register is Zero */ #define SII_TBE 0x0800 /* Transmit Buffer Empty */ #define SII_IBF 0x0400 /* Input Buffer Full */ #define SII_IPE 0x0200 /* Incoming Parity Error */ #define SII_OBB 0x0100 /* Odd Byte Boundry */ #define SII_MIS 0x0010 /* Phase Mismatch */ #define SII_ATN 0x0008 /* ATN set by initiator if in Target mode */ #define SII_MSG 0x0004 /* current bus state of MSG */ #define SII_CD 0x0002 /* current bus state of C/D */ #define SII_IO 0x0001 /* current bus state of I/O */ #define SII_PHASE_MSK 0x0007 /* Phase Mask */ /* * The different phases. */ #define SII_MSG_IN_PHASE 0x7 #define SII_MSG_OUT_PHASE 0x6 #define SII_STATUS_PHASE 0x3 #define SII_CMD_PHASE 0x2 #define SII_DATA_IN_PHASE 0x1 #define SII_DATA_OUT_PHASE 0x0 /* * COMM - Command Register */ #define SII_DMA 0x8000 /* DMA mode */ #define SII_DO_RST 0x4000 /* Assert reset on SCSI bus for 25 usecs */ #define SII_RSL 0x1000 /* 0 = select, 1 = reselect desired device */ /* Commands: I - Initiator, T - Target, D - Disconnected */ #define SII_INXFER 0x0800 /* Information Transfer command (I,T) */ #define SII_SELECT 0x0400 /* Select command (D) */ #define SII_REQDATA 0x0200 /* Request Data command (T) */ #define SII_DISCON 0x0100 /* Disconnect command (I,T,D) */ #define SII_CHRESET 0x0080 /* Chip Reset command (I,T,D) */ /* Command state bits same as connection status register */ /* Command phase bits same as data transfer status register */ /* * DICTRL - Diagnostic Control Register */ #define SII_PRE 0x4 /* Enable the SII to drive the SCSI bus */ #define SII_WAIT_COUNT 10000 /* Delay count used for the SII chip */ /* * Max DMA transfer length for SII * The SII chip only has a 13 bit counter. If 8192 is used as the max count, * you can't tell the difference between a count of zero and 8192. * 8190 is used instead of 8191 so the count is even. */ #define SII_MAX_DMA_XFER_LENGTH 8192 #endif /* _SII */