/* $NetBSD: i82801lpcreg.h,v 1.12 2014/12/26 05:09:03 msaitoh Exp $ */ /*- * Copyright (c) 2004 The NetBSD Foundation, Inc. * All rights reserved. * * This code is derived from software contributed to The NetBSD Foundation * by Minoura Makoto. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * * THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED * TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE * POSSIBILITY OF SUCH DAMAGE. */ /* * Intel 82801 Series I/O Controller Hub (ICH) -- LPC Interface Bridge part * register definitions. */ #ifndef _DEV_IC_I82801LPCREG_H_ #define _DEV_IC_I82801LPCREG_H_ /* * PCI configuration registers */ #define LPCIB_PCI_PMBASE 0x40 #define LPCIB_PCI_PM_SIZE 0x00000080 #define LPCIB_PCI_ACPI_CNTL 0x44 # define LPCIB_PCI_ACPI_CNTL_EN (1 << 4) /* GPIO config registers ICH6+ */ #define LPCIB_PCI_GPIO_BASE_ICH6 0x48 #define LPCIB_PCI_GPIO_CNTL_ICH6 0x4c #define LPCIB_PCI_BIOS_CNTL 0x4c /* actually 0x4e */ #define LPCIB_PCI_BIOS_CNTL_BWE (0x0001 << 16) /* write enable */ #define LPCIB_PCI_BIOS_CNTL_BLE (0x0002 << 16) /* lock enable */ #define LPCIB_PCI_TCO_CNTL 0x54 /* GPIO config registers ICH0-ICH5 */ #define LPCIB_PCI_GPIO_BASE 0x58 #define LPCIB_PCI_GPIO_SIZE 0x00000080 #define LPCIB_PCI_GPIO_CNTL 0x5c #define LPCIB_PCI_GPIO_CNTL_EN (1 << 4) #define LPCIB_PCI_PIRQA_ROUT 0x60 #define LPCIB_PCI_PIRQB_ROUT 0x61 #define LPCIB_PCI_PIRQC_ROUT 0x62 #define LPCIB_PCI_PIRQD_ROUT 0x63 #define LPCIB_PCI_SIRQ_CNTL 0x64 #define LPCIB_PCI_PIRQE_ROUT 0x68 #define LPCIB_PCI_PIRQF_ROUT 0x69 #define LPCIB_PCI_PIRQG_ROUT 0x6a #define LPCIB_PCI_PIRQH_ROUT 0x6b #define LPCIB_PCI_D31_ERR_CFG 0x88 #define LPCIB_PCI_D31_ERR_STS 0x8a #define LPCIB_PCI_PCI_DMA_C 0x90 #define LPCIB_PCI_GEN_PMCON_1 0xa0 # define LPCIB_PCI_GEN_PMCON_1_SS_EN 0x08 #define LPCIB_PCI_GEN_PMCON_2 0xa2 #define LPCIB_PCI_GEN_PMCON_3 0xa4 #define LPCIB_PCI_STPCLK_DEL 0xa8 #define LPCIB_PCI_GPI_ROUT 0xb8 #define LPCIB_PCI_TRP_FWD_EN 0xc0 #define LPCIB_PCI_MON4_TRP_RNG 0xc4 #define LPCIB_PCI_MON5_TRP_RNG 0xc5 #define LPCIB_PCI_MON6_TRP_RNG 0xc6 #define LPCIB_PCI_MON7_TRP_RNG 0xc7 #define LPCIB_PCI_MON_TRP_MSK 0xcc #define LPCIB_PCI_GEN_CNTL 0xd0 #define LPCIB_ICH5_HPTC_EN 0x00020000 #define LPCIB_ICH5_HPTC_WIN_MASK 0x0000c000 #define LPCIB_ICH5_HPTC_0000 0x00000000 #define LPCIB_ICH5_HPTC_0000_BASE 0xfed00000 #define LPCIB_ICH5_HPTC_1000 0x00008000 #define LPCIB_ICH5_HPTC_1000_BASE 0xfed01000 #define LPCIB_ICH5_HPTC_2000 0x00010000 #define LPCIB_ICH5_HPTC_2000_BASE 0xfed02000 #define LPCIB_ICH5_HPTC_3000 0x00018000 #define LPCIB_ICH5_HPTC_3000_BASE 0xfed03000 #define LPCIB_PCI_GEN_STA 0xd4 # define LPCIB_PCI_GEN_STA_SAFE_MODE (1 << 2) # define LPCIB_PCI_GEN_STA_NO_REBOOT (1 << 1) #define LPCIB_PCI_BACK_CNTL 0xd5 #define LPCIB_PCI_RTC_CONF 0xd8 #define LPCIB_PCI_COM_DEC 0xe0 #define LPCIB_PCI_LPCFDD_DEC 0xe1 #define LPCIB_PCI_SND_DEC 0xe2 #define LPCIB_PCI_FWH_DEC_EN1 0xe3 #define LPCIB_PCI_GEN1_DEC 0xe4 #define LPCIB_PCI_LPC_EN 0xe6 #define LPCIB_PCI_FWH_SEL1 0xe8 #define LPCIB_PCI_GEN2_DEC 0xec #define LPCIB_PCI_FWH_SEL2 0xee #define LPCIB_PCI_FWH_DEC_EN2 0xf0 #define LPCIB_PCI_FUNC_DIS 0xf2 /* * Power management I/O registers * (offset from PMBASE) */ #define LPCIB_PM1_STS 0x00 /* ACPI PM1a_EVT_BLK fixed event status */ #define LPCIB_PM1_EN 0x02 /* ACPI PM1a_EVT_BLK fixed event enable */ #define LPCIB_PM1_CNT 0x04 /* ACPI PM1a_CNT_BLK */ #define LPCIB_PM1_TMR 0x08 /* ACPI PMTMR_BLK power mgmt timer */ #define LPCIB_PROC_CNT 0x10 /* ACPI P_BLK processor control */ #define LPCIB_LV2 0x14 /* ACPI P_BLK processor C2 control */ #define LPCIB_PM_CTRL 0x20 /* ACPI Power Management Control */ # define LPCIB_PM_SS_STATE_LOW 0x01 /* SpeedStep Low Power State */ #define LPCIB_GPE0_STS 0x28 /* ACPI GPE0_BLK GPE0 status */ #define LPCIB_GPE0_EN 0x2c /* ACPI GPE0_BLK GPE0 enable */ #define LPCIB_SMI_EN 0x30 # define LPCIB_SMI_EN_INTEL_USB2_EN (1 << 18) # define LPCIB_SMI_EN_LEGACY_USB2_EN (1 << 17) # define LPCIB_SMI_EN_PERIODIC_EN (1 << 14) # define LPCIB_SMI_EN_TCO_EN (1 << 13) # define LPCIB_SMI_EN_MCSMI_EN (1 << 11) # define LPCIB_SMI_EN_BIOS_RLS (1 << 7) # define LPCIB_SMI_EN_SWSMI_TMR_EN (1 << 6) # define LPCIB_SMI_EN_APMC_EN (1 << 5) # define LPCIB_SMI_EN_SLP_SMI_EN (1 << 4) # define LPCIB_SMI_EN_LEGACY_USB_EN (1 << 3) # define LPCIB_SMI_EN_BIOS_EN (1 << 2) # define LPCIB_SMI_EN_EOS (1 << 1) # define LPCIB_SMI_EN_GBL_SMI_EN (1 << 0) #define LPCIB_SMI_STS 0x34 #define LPCIB_ALT_GP_SMI_EN 0x38 #define LPCIB_ALT_GP_SMI_STS 0x3a #define LPCIB_MON_SMI 0x40 #define LPCIB_DEVACT_STS 0x44 #define LPCIB_DEVTRAP_EN 0x48 #define LPCIB_BUS_ADDR_TRACK 0x4c #define LPCIB_BUS_CYC_TRACK 0x4e #define LPCIB_PM_SS_CNTL 0x50 /* SpeedStep control */ # define LPCIB_PM_SS_CNTL_ARB_DIS 0x01 /* disable arbiter */ /* * General Purpose I/O Registers * (offset from GPIO_BASE) */ #define LPCIB_GPIO_GPIO_USE_SEL 0x00 #define LPCIB_GPIO_GP_IO_SEL 0x04 #define LPCIB_GPIO_GP_LVL 0x0c #define LPCIB_GPIO_GPO_TTL 0x14 #define LPCIB_GPIO_GPO_BLINK 0x18 #define LPCIB_GPIO_GPI_INV 0x2c #define LPCIB_GPIO_GPIO_USE_SEL2 0x30 #define LPCIB_GPIO_GP_IO_SEL2 0x34 #define LPCIB_GPIO_GP_LVL2 0x38 /* * SMBus controller registers. */ /* PCI configuration registers */ #define LPCIB_SMB_BASE 0x20 /* SMBus base address */ #define LPCIB_SMB_HOSTC 0x40 /* host configuration */ #define LPCIB_SMB_HOSTC_HSTEN (1 << 0) /* enable host controller */ #define LPCIB_SMB_HOSTC_SMIEN (1 << 1) /* generate SMI */ #define LPCIB_SMB_HOSTC_I2CEN (1 << 2) /* enable I2C commands */ /* SMBus I/O registers */ #define LPCIB_SMB_HS 0x00 /* host status */ #define LPCIB_SMB_HS_BUSY (1 << 0) /* running a command */ #define LPCIB_SMB_HS_INTR (1 << 1) /* command completed */ #define LPCIB_SMB_HS_DEVERR (1 << 2) /* command error */ #define LPCIB_SMB_HS_BUSERR (1 << 3) /* transaction collision */ #define LPCIB_SMB_HS_FAILED (1 << 4) /* failed bus transaction */ #define LPCIB_SMB_HS_SMBAL (1 << 5) /* SMBALERT# asserted */ #define LPCIB_SMB_HS_INUSE (1 << 6) /* bus semaphore */ #define LPCIB_SMB_HS_BDONE (1 << 7) /* byte received/transmitted */ #define LPCIB_SMB_HS_BITS "\020\001BUSY\002INTR\003DEVERR\004BUSERR\005FAILED\006SMBAL\007INUSE\010BDONE" #define LPCIB_SMB_HC 0x02 /* host control */ #define LPCIB_SMB_HC_INTREN (1 << 0) /* enable interrupts */ #define LPCIB_SMB_HC_KILL (1 << 1) /* kill current transaction */ #define LPCIB_SMB_HC_CMD_QUICK (0 << 2) /* QUICK command */ #define LPCIB_SMB_HC_CMD_BYTE (1 << 2) /* BYTE command */ #define LPCIB_SMB_HC_CMD_BDATA (2 << 2) /* BYTE DATA command */ #define LPCIB_SMB_HC_CMD_WDATA (3 << 2) /* WORD DATA command */ #define LPCIB_SMB_HC_CMD_PCALL (4 << 2) /* PROCESS CALL command */ #define LPCIB_SMB_HC_CMD_BLOCK (5 << 2) /* BLOCK command */ #define LPCIB_SMB_HC_CMD_I2CREAD (6 << 2) /* I2C READ command */ #define LPCIB_SMB_HC_CMD_BLOCKP (7 << 2) /* BLOCK PROCESS command */ #define LPCIB_SMB_HC_LASTB (1 << 5) /* last byte in block */ #define LPCIB_SMB_HC_START (1 << 6) /* start transaction */ #define LPCIB_SMB_HC_PECEN (1 << 7) /* enable PEC */ #define LPCIB_SMB_HCMD 0x03 /* host command */ #define LPCIB_SMB_TXSLVA 0x04 /* transmit slave address */ #define LPCIB_SMB_TXSLVA_READ (1 << 0) /* read direction */ #define LPCIB_SMB_TXSLVA_ADDR(x) (((x) & 0x7f) << 1) /* 7-bit address */ #define LPCIB_SMB_HD0 0x05 /* host data 0 */ #define LPCIB_SMB_HD1 0x06 /* host data 1 */ #define LPCIB_SMB_HBDB 0x07 /* host block data byte */ #define LPCIB_SMB_PEC 0x08 /* PEC data */ #define LPCIB_SMB_RXSLVA 0x09 /* receive slave address */ #define LPCIB_SMB_SD 0x0a /* receive slave data */ #define LPCIB_SMB_SD_MSG0(x) ((x) & 0xff) /* data message byte 0 */ #define LPCIB_SMB_SD_MSG1(x) ((x) >> 8) /* data message byte 1 */ #define LPCIB_SMB_AS 0x0c /* auxiliary status */ #define LPCIB_SMB_AS_CRCE (1 << 0) /* CRC error */ #define LPCIB_SMB_AS_TCO (1 << 1) /* advanced TCO mode */ #define LPCIB_SMB_AC 0x0d /* auxiliary control */ #define LPCIB_SMB_AC_AAC (1 << 0) /* automatically append CRC */ #define LPCIB_SMB_AC_E32B (1 << 1) /* enable 32-byte buffer */ #define LPCIB_SMB_SMLPC 0x0e /* SMLink pin control */ #define LPCIB_SMB_SMLPC_LINK0 (1 << 0) /* SMLINK0 pin state */ #define LPCIB_SMB_SMLPC_LINK1 (1 << 1) /* SMLINK1 pin state */ #define LPCIB_SMB_SMLPC_CLKC (1 << 2) /* SMLINK0 pin is untouched */ #define LPCIB_SMB_SMBPC 0x0f /* SMBus pin control */ #define LPCIB_SMB_SMBPC_CLK (1 << 0) /* SMBCLK pin state */ #define LPCIB_SMB_SMBPC_DATA (1 << 1) /* SMBDATA pin state */ #define LPCIB_SMB_SMBPC_CLKC (1 << 2) /* SMBCLK pin is untouched */ #define LPCIB_SMB_SS 0x10 /* slave status */ #define LPCIB_SMB_SS_HN (1 << 0) /* Host Notify command */ #define LPCIB_SMB_SCMD 0x11 /* slave command */ #define LPCIB_SMB_SCMD_INTREN (1 << 0) /* enable interrupts on HN */ #define LPCIB_SMB_SCMD_WKEN (1 << 1) /* wake on HN */ #define LPCIB_SMB_SCMD_SMBALDS (1 << 2) /* disable SMBALERT# intr */ #define LPCIB_SMB_NDADDR 0x14 /* notify device address */ #define LPCIB_SMB_NDADDR_ADDR(x) ((x) >> 1) /* 7-bit address */ #define LPCIB_SMB_NDLOW 0x16 /* notify data low byte */ #define LPCIB_SMB_NDHIGH 0x17 /* notify data high byte */ /* ICH Chipset Configuration Registers (ICH6 and newer) */ #define LPCIB_RCBA 0xf0 #define LPCIB_RCBA_EN 0x00000001 #define LPCIB_RCBA_SIZE 0x00004000 #define LPCIB_GCS_OFFSET 0x3410 #define LPCIB_GCS_NO_REBOOT 0x20 #define LPCIB_RCBA_HPTC 0x00003404 #define LPCIB_RCBA_HPTC_EN 0x00000080 #define LPCIB_RCBA_HPTC_WIN_MASK 0x00000003 #define LPCIB_RCBA_HPTC_0000 0x00000000 #define LPCIB_RCBA_HPTC_0000_BASE 0xfed00000 #define LPCIB_RCBA_HPTC_1000 0x00000001 #define LPCIB_RCBA_HPTC_1000_BASE 0xfed01000 #define LPCIB_RCBA_HPTC_2000 0x00000002 #define LPCIB_RCBA_HPTC_2000_BASE 0xfed02000 #define LPCIB_RCBA_HPTC_3000 0x00000003 #define LPCIB_RCBA_HPTC_3000_BASE 0xfed03000 /* * System management TCO registers * (offset from PMBASE) */ #define LPCIB_TCO_BASE 0x60 #define LPCIB_TCO_RLD (LPCIB_TCO_BASE+0x00) #define LPCIB_TCO_TMR (LPCIB_TCO_BASE+0x01) #define LPCIB_TCO_TMR2 (LPCIB_TCO_BASE+0x12) /* ICH6 and newer */ # define LPCIB_TCO_TMR_MASK 0x3f #define LPCIB_TCO_DAT_IN (LPCIB_TCO_BASE+0x02) #define LPCIB_TCO_DAT_OUT (LPCIB_TCO_BASE+0x03) #define LPCIB_TCO1_STS (LPCIB_TCO_BASE+0x04) # define LPCIB_TCO1_STS_TIMEOUT 0x08 #define LPCIB_TCO2_STS (LPCIB_TCO_BASE+0x06) # define LPCIB_TCO2_STS_BOOT_STS 0x04 # define LPCIB_TCO2_STS_SECONDS_TO_STS 0x02 #define LPCIB_TCO1_CNT (LPCIB_TCO_BASE+0x08) # define LPCIB_TCO1_CNT_TCO_LOCK (1 << 12) # define LPCIB_TCO1_CNT_TCO_TMR_HLT (1 << 11) # define LPCIB_TCO1_CNT_SEND_NOW (1 << 10) # define LPCIB_TCO1_CNT_NMI2SMI_EN (1 << 9) # define LPCIB_TCO1_CNT_NMI_NOW (1 << 8) #define LPCIB_TCO2_CNT (LPCIB_TCO_BASE+0x0a) #define LPCIB_TCO_MESSAGE1 (LPCIB_TCO_BASE+0x0c) #define LPCIB_TCO_MESSAGE2 (LPCIB_TCO_BASE+0x0d) #define LPCIB_TCO_WDSTATUS (LPCIB_TCO_BASE+0x0e) #define LPCIB_SW_IRQ_GEN (LPCIB_TCO_BASE+0x10) /* * TCO timer tick. ICH datasheets say: * - The timer is clocked at approximately 0.6 seconds * - 6 bit; values of 0-3 will be ignored and should not be attempted */ static __inline int lpcib_tcotimer_tick_to_second(int ltick) { return ltick * 6 / 10; } static __inline int lpcib_tcotimer_second_to_tick(int ltick) { return ltick * 10 / 6; } #define LPCIB_TCOTIMER_MIN_TICK 4 #define LPCIB_TCOTIMER2_MIN_TICK 2 #define LPCIB_TCOTIMER_MAX_TICK 0x3f /* 39 seconds max */ #define LPCIB_TCOTIMER2_MAX_TICK 0x265 /* 613 seconds max */ #endif /* _DEV_IC_I82801LPCREG_H_ */