/* $NetBSD: intersil7170reg.h,v 1.2 2008/04/28 20:23:50 martin Exp $ */ /*- * Copyright (c) 1996 The NetBSD Foundation, Inc. * All rights reserved. * * This code is derived from software contributed to The NetBSD Foundation * by Adam Glass. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * * THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED * TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE * POSSIBILITY OF SUCH DAMAGE. */ #ifndef _INTERSIL7170REG_H_ #define _INTERSIL7170REG_H_ /* * Driver support for the intersil7170 used in sun[34]s to provide * real time clock and time-of-day support. * * Derived from: datasheet "ICM7170 a uP-Compatible Real-Time Clock" * document #301680-005, Dec 85 * * Note that this device provides both time-of-day and interval timer * functionality. Both functions use the same control registers. On top * of that, the command control register is write-only. Currently, this * driver assumes that the interval timer is to be enabled, and hence * always sets/restores the INTERSIL_CMD_IENABLE control bit when * manipulating the TOD. */ struct intersil_dt { /* from p. 7 of 10 */ uint8_t dt_csec; uint8_t dt_hour; uint8_t dt_min; uint8_t dt_sec; uint8_t dt_month; uint8_t dt_day; uint8_t dt_year; uint8_t dt_dow; }; struct intersil7170 { struct intersil_dt counters; struct intersil_dt clk_ram; /* should be ok as both are word aligned */ uint8_t clk_intr_reg; uint8_t clk_cmd_reg; }; /* Indices to time-of-day clock registers */ #define INTERSIL_ICSEC 0 #define INTERSIL_IHOUR 1 #define INTERSIL_IMIN 2 #define INTERSIL_ISEC 3 #define INTERSIL_IMON 4 #define INTERSIL_IDAY 5 #define INTERSIL_IYEAR 6 #define INTERSIL_IDOW 7 #define INTERSIL_IINTR 16 #define INTERSIL_ICMD 17 /* bit assignments for command register, p. 6 of 10, write-only */ #define INTERSIL_CMD_FREQ_32K 0x0 #define INTERSIL_CMD_FREQ_1M 0x1 #define INTERSIL_CMD_FREQ_2M 0x2 #define INTERSIL_CMD_FREQ_4M 0x3 #define INTERSIL_CMD_12HR_MODE 0x0 #define INTERSIL_CMD_24HR_MODE 0x4 #define INTERSIL_CMD_STOP 0x0 #define INTERSIL_CMD_RUN 0x8 #define INTERSIL_CMD_IDISABLE 0x0 #define INTERSIL_CMD_IENABLE 0x10 #define INTERSIL_CMD_TEST_MODE 0x20 #define INTERSIL_CMD_NORMAL_MODE 0x0 #define INTERSIL_COMMAND(run, interrupt) \ ((run) | (interrupt) | INTERSIL_CMD_FREQ_32K | \ INTERSIL_CMD_24HR_MODE | INTERSIL_CMD_NORMAL_MODE) /* bit assignments for interrupt register r/w, p 7 of 10 */ #define INTERSIL_INTER_ALARM 0x1 /* r/w */ #define INTERSIL_INTER_CSECONDS 0x2 /* r/w */ #define INTERSIL_INTER_DSECONDS 0x4 /* r/w */ #define INTERSIL_INTER_SECONDS 0x8 /* r/w */ #define INTERSIL_INTER_MINUTES 0x10 /* r/w */ #define INTERSIL_INTER_HOURS 0x20 /* r/w */ #define INTERSIL_INTER_DAYS 0x40 /* r/w */ #define INTERSIL_INTER_PENDING 0x80 /* read-only */ #define INTERSIL_INTER_BITS \ "\20\10PENDING\7DAYS\6HRS\5MIN\4SCDS\3DSEC\2CSEC\1ALARM" #endif /* _INTERSIL7170REG_H_ */