/* $NetBSD: ncr53c9x.c,v 1.147 2017/01/11 07:16:48 skrll Exp $ */ /*- * Copyright (c) 1998, 2002 The NetBSD Foundation, Inc. * All rights reserved. * * This code is derived from software contributed to The NetBSD Foundation * by Charles M. Hannum. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * * THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED * TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE * POSSIBILITY OF SUCH DAMAGE. */ /* * Copyright (c) 1994 Peter Galbavy * Copyright (c) 1995 Paul Kranenburg * All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * 3. All advertising materials mentioning features or use of this software * must display the following acknowledgement: * This product includes software developed by Peter Galbavy * 4. The name of the author may not be used to endorse or promote products * derived from this software without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE * DISCLAIMED. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE * POSSIBILITY OF SUCH DAMAGE. */ /* * Based on aic6360 by Jarle Greipsland * * Acknowledgements: Many of the algorithms used in this driver are * inspired by the work of Julian Elischer (julian@tfs.com) and * Charles Hannum (mycroft@duality.gnu.ai.mit.edu). Thanks a million! */ #include __KERNEL_RCSID(0, "$NetBSD: ncr53c9x.c,v 1.147 2017/01/11 07:16:48 skrll Exp $"); #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include int ncr53c9x_debug = NCR_SHOWMISC; /*NCR_SHOWPHASE|NCR_SHOWMISC|NCR_SHOWTRAC|NCR_SHOWCMDS;*/ #ifdef DEBUG int ncr53c9x_notag = 0; #endif static void ncr53c9x_readregs(struct ncr53c9x_softc *); static void ncr53c9x_select(struct ncr53c9x_softc *, struct ncr53c9x_ecb *); static int ncr53c9x_reselect(struct ncr53c9x_softc *, int, int, int); #if 0 static void ncr53c9x_scsi_reset(struct ncr53c9x_softc *); #endif static void ncr53c9x_clear(struct ncr53c9x_softc *, scsipi_xfer_result_t); static int ncr53c9x_poll(struct ncr53c9x_softc *, struct scsipi_xfer *, int); static void ncr53c9x_sched(struct ncr53c9x_softc *); static void ncr53c9x_done(struct ncr53c9x_softc *, struct ncr53c9x_ecb *); static void ncr53c9x_msgin(struct ncr53c9x_softc *); static void ncr53c9x_msgout(struct ncr53c9x_softc *); static void ncr53c9x_timeout(void *arg); static void ncr53c9x_watch(void *arg); static void ncr53c9x_dequeue(struct ncr53c9x_softc *, struct ncr53c9x_ecb *); static int ncr53c9x_ioctl(struct scsipi_channel *, u_long, void *, int, struct proc *); void ncr53c9x_sense(struct ncr53c9x_softc *, struct ncr53c9x_ecb *); void ncr53c9x_free_ecb(struct ncr53c9x_softc *, struct ncr53c9x_ecb *); struct ncr53c9x_ecb *ncr53c9x_get_ecb(struct ncr53c9x_softc *, int); static inline int ncr53c9x_stp2cpb(struct ncr53c9x_softc *, int); static inline void ncr53c9x_setsync(struct ncr53c9x_softc *, struct ncr53c9x_tinfo *); void ncr53c9x_update_xfer_mode (struct ncr53c9x_softc *, int); static struct ncr53c9x_linfo *ncr53c9x_lunsearch(struct ncr53c9x_tinfo *, int64_t lun); static void ncr53c9x_wrfifo(struct ncr53c9x_softc *, uint8_t *, int); static int ncr53c9x_rdfifo(struct ncr53c9x_softc *, int); #define NCR_RDFIFO_START 0 #define NCR_RDFIFO_CONTINUE 1 #define NCR_SET_COUNT(sc, size) do { \ NCR_WRITE_REG((sc), NCR_TCL, (size)); \ NCR_WRITE_REG((sc), NCR_TCM, (size) >> 8); \ if ((sc->sc_cfg2 & NCRCFG2_FE) || \ (sc->sc_rev == NCR_VARIANT_FAS366)) { \ NCR_WRITE_REG((sc), NCR_TCH, (size) >> 16); \ } \ if (sc->sc_rev == NCR_VARIANT_FAS366) { \ NCR_WRITE_REG(sc, NCR_RCH, 0); \ } \ } while (/* CONSTCOND */0) static int ecb_pool_initialized = 0; static struct pool ecb_pool; /* * Names for the NCR53c9x variants, corresponding to the variant tags * in ncr53c9xvar.h. */ static const char *ncr53c9x_variant_names[] = { "ESP100", "ESP100A", "ESP200", "NCR53C94", "NCR53C96", "ESP406", "FAS408", "FAS216", "AM53C974", "FAS366/HME", "NCR53C90 (86C01)", }; /* * Search linked list for LUN info by LUN id. */ static struct ncr53c9x_linfo * ncr53c9x_lunsearch(struct ncr53c9x_tinfo *ti, int64_t lun) { struct ncr53c9x_linfo *li; LIST_FOREACH(li, &ti->luns, link) if (li->lun == lun) return li; return NULL; } /* * Attach this instance, and then all the sub-devices */ void ncr53c9x_attach(struct ncr53c9x_softc *sc) { struct scsipi_adapter *adapt = &sc->sc_adapter; struct scsipi_channel *chan = &sc->sc_channel; mutex_init(&sc->sc_lock, MUTEX_DEFAULT, IPL_BIO); callout_init(&sc->sc_watchdog, 0); /* * Note, the front-end has set us up to print the chip variation. */ if (sc->sc_rev >= NCR_VARIANT_MAX) { aprint_error(": unknown variant %d, devices not attached\n", sc->sc_rev); return; } aprint_normal(": %s, %dMHz, SCSI ID %d\n", ncr53c9x_variant_names[sc->sc_rev], sc->sc_freq, sc->sc_id); sc->sc_ntarg = (sc->sc_rev == NCR_VARIANT_FAS366) ? 16 : 8; /* * Allocate SCSI message buffers. * Front-ends can override allocation to avoid alignment * handling in the DMA engines. Note that that ncr53c9x_msgout() * can request a 1 byte DMA transfer. */ if (sc->sc_omess == NULL) sc->sc_omess = malloc(NCR_MAX_MSG_LEN, M_DEVBUF, M_NOWAIT); if (sc->sc_imess == NULL) sc->sc_imess = malloc(NCR_MAX_MSG_LEN + 1, M_DEVBUF, M_NOWAIT); sc->sc_tinfo = malloc(sc->sc_ntarg * sizeof(sc->sc_tinfo[0]), M_DEVBUF, M_NOWAIT | M_ZERO); if (sc->sc_omess == NULL || sc->sc_imess == NULL || sc->sc_tinfo == NULL) { aprint_error_dev(sc->sc_dev, "out of memory\n"); return; } /* * Treat NCR53C90 with the 86C01 DMA chip exactly as ESP100 * from now on. */ if (sc->sc_rev == NCR_VARIANT_NCR53C90_86C01) sc->sc_rev = NCR_VARIANT_ESP100; sc->sc_ccf = FREQTOCCF(sc->sc_freq); /* The value *must not* be == 1. Make it 2 */ if (sc->sc_ccf == 1) sc->sc_ccf = 2; /* * The recommended timeout is 250ms. This register is loaded * with a value calculated as follows, from the docs: * * (timout period) x (CLK frequency) * reg = ------------------------------------- * 8192 x (Clock Conversion Factor) * * Since CCF has a linear relation to CLK, this generally computes * to the constant of 153. */ sc->sc_timeout = ((250 * 1000) * sc->sc_freq) / (8192 * sc->sc_ccf); /* CCF register only has 3 bits; 0 is actually 8 */ sc->sc_ccf &= 7; /* * Fill in the scsipi_adapter. */ adapt->adapt_dev = sc->sc_dev; adapt->adapt_nchannels = 1; adapt->adapt_openings = 256; adapt->adapt_max_periph = 256; adapt->adapt_ioctl = ncr53c9x_ioctl; /* adapt_request initialized by front-end */ /* adapt_minphys initialized by front-end */ /* * Fill in the scsipi_channel. */ memset(chan, 0, sizeof(*chan)); chan->chan_adapter = adapt; chan->chan_bustype = &scsi_bustype; chan->chan_channel = 0; chan->chan_ntargets = sc->sc_ntarg; chan->chan_nluns = 8; chan->chan_id = sc->sc_id; /* * Add reference to adapter so that we drop the reference after * config_found() to make sure the adapter is disabled. */ if (scsipi_adapter_addref(adapt) != 0) { aprint_error_dev(sc->sc_dev, "unable to enable controller\n"); return; } /* Reset state & bus */ sc->sc_cfflags = device_cfdata(sc->sc_dev)->cf_flags; sc->sc_state = 0; ncr53c9x_init(sc, 0); /* no bus reset yet, leave that to scsibus* */ /* * Now try to attach all the sub-devices */ sc->sc_child = config_found(sc->sc_dev, &sc->sc_channel, scsiprint); scsipi_adapter_delref(adapt); callout_reset(&sc->sc_watchdog, 60 * hz, ncr53c9x_watch, sc); } int ncr53c9x_detach(struct ncr53c9x_softc *sc, int flags) { struct ncr53c9x_linfo *li, *nextli; int t; int error; callout_stop(&sc->sc_watchdog); if (sc->sc_tinfo) { /* Cancel all commands. */ ncr53c9x_clear(sc, XS_DRIVER_STUFFUP); /* Free logical units. */ for (t = 0; t < sc->sc_ntarg; t++) { for (li = LIST_FIRST(&sc->sc_tinfo[t].luns); li; li = nextli) { nextli = LIST_NEXT(li, link); free(li, M_DEVBUF); } } } if (sc->sc_child) { error = config_detach(sc->sc_child, flags); if (error) return error; } if (sc->sc_imess) free(sc->sc_imess, M_DEVBUF); if (sc->sc_omess) free(sc->sc_omess, M_DEVBUF); mutex_destroy(&sc->sc_lock); return 0; } /* * This is the generic ncr53c9x reset function. It does not reset the SCSI bus, * only this controller, but kills any on-going commands, and also stops * and resets the DMA. * * After reset, registers are loaded with the defaults from the attach * routine above. */ void ncr53c9x_reset(struct ncr53c9x_softc *sc) { /* reset DMA first */ NCRDMA_RESET(sc); /* reset SCSI chip */ NCRCMD(sc, NCRCMD_RSTCHIP); NCRCMD(sc, NCRCMD_NOP); DELAY(500); /* do these backwards, and fall through */ switch (sc->sc_rev) { case NCR_VARIANT_ESP406: case NCR_VARIANT_FAS408: NCR_WRITE_REG(sc, NCR_CFG5, sc->sc_cfg5 | NCRCFG5_SINT); NCR_WRITE_REG(sc, NCR_CFG4, sc->sc_cfg4); case NCR_VARIANT_AM53C974: case NCR_VARIANT_FAS216: case NCR_VARIANT_NCR53C94: case NCR_VARIANT_NCR53C96: case NCR_VARIANT_ESP200: sc->sc_features |= NCR_F_HASCFG3; NCR_WRITE_REG(sc, NCR_CFG3, sc->sc_cfg3); case NCR_VARIANT_ESP100A: sc->sc_features |= NCR_F_SELATN3; NCR_WRITE_REG(sc, NCR_CFG2, sc->sc_cfg2); case NCR_VARIANT_ESP100: NCR_WRITE_REG(sc, NCR_CFG1, sc->sc_cfg1); NCR_WRITE_REG(sc, NCR_CCF, sc->sc_ccf); NCR_WRITE_REG(sc, NCR_SYNCOFF, 0); NCR_WRITE_REG(sc, NCR_TIMEOUT, sc->sc_timeout); break; case NCR_VARIANT_FAS366: sc->sc_features |= NCR_F_HASCFG3 | NCR_F_FASTSCSI | NCR_F_SELATN3; sc->sc_cfg3 = NCRFASCFG3_FASTCLK | NCRFASCFG3_OBAUTO; sc->sc_cfg3_fscsi = NCRFASCFG3_FASTSCSI; NCR_WRITE_REG(sc, NCR_CFG3, sc->sc_cfg3); sc->sc_cfg2 = 0; /* NCRCFG2_HMEFE| NCRCFG2_HME32 */ NCR_WRITE_REG(sc, NCR_CFG2, sc->sc_cfg2); NCR_WRITE_REG(sc, NCR_CFG1, sc->sc_cfg1); NCR_WRITE_REG(sc, NCR_CCF, sc->sc_ccf); NCR_WRITE_REG(sc, NCR_SYNCOFF, 0); NCR_WRITE_REG(sc, NCR_TIMEOUT, sc->sc_timeout); break; default: printf("%s: unknown revision code, assuming ESP100\n", device_xname(sc->sc_dev)); NCR_WRITE_REG(sc, NCR_CFG1, sc->sc_cfg1); NCR_WRITE_REG(sc, NCR_CCF, sc->sc_ccf); NCR_WRITE_REG(sc, NCR_SYNCOFF, 0); NCR_WRITE_REG(sc, NCR_TIMEOUT, sc->sc_timeout); } if (sc->sc_rev == NCR_VARIANT_AM53C974) NCR_WRITE_REG(sc, NCR_AMDCFG4, sc->sc_cfg4); #if 0 printf("%s: ncr53c9x_reset: revision %d\n", device_xname(sc->sc_dev), sc->sc_rev); printf("%s: ncr53c9x_reset: cfg1 0x%x, cfg2 0x%x, cfg3 0x%x, " "ccf 0x%x, timeout 0x%x\n", device_xname(sc->sc_dev), sc->sc_cfg1, sc->sc_cfg2, sc->sc_cfg3, sc->sc_ccf, sc->sc_timeout); #endif } #if 0 /* * Reset the SCSI bus, but not the chip */ void ncr53c9x_scsi_reset(struct ncr53c9x_softc *sc) { (*sc->sc_glue->gl_dma_stop)(sc); printf("%s: resetting SCSI bus\n", device_xname(sc->sc_dev)); NCRCMD(sc, NCRCMD_RSTSCSI); } #endif /* * Clear all commands */ void ncr53c9x_clear(struct ncr53c9x_softc *sc, scsipi_xfer_result_t result) { struct ncr53c9x_ecb *ecb; struct ncr53c9x_linfo *li; int i, r; /* Cancel any active commands. */ sc->sc_state = NCR_CLEANING; sc->sc_msgify = 0; ecb = sc->sc_nexus; if (ecb != NULL) { ecb->xs->error = result; ncr53c9x_done(sc, ecb); } /* Cancel outstanding disconnected commands on each LUN */ for (r = 0; r < sc->sc_ntarg; r++) { LIST_FOREACH(li, &sc->sc_tinfo[r].luns, link) { ecb = li->untagged; if (ecb != NULL) { li->untagged = NULL; /* * XXXXXXX * * Should we terminate a command * that never reached the disk? */ li->busy = 0; ecb->xs->error = result; ncr53c9x_done(sc, ecb); } for (i = 0; i < 256; i++) { ecb = li->queued[i]; if (ecb != NULL) { li->queued[i] = NULL; ecb->xs->error = result; ncr53c9x_done(sc, ecb); } } li->used = 0; } } } /* * Initialize ncr53c9x state machine */ void ncr53c9x_init(struct ncr53c9x_softc *sc, int doreset) { int r; NCR_MISC(("[NCR_INIT(%d) %d] ", doreset, sc->sc_state)); if (!ecb_pool_initialized) { /* All instances share this pool */ pool_init(&ecb_pool, sizeof(struct ncr53c9x_ecb), 0, 0, 0, "ncr53c9x_ecb", NULL, IPL_BIO); /* make sure to always have some items to play with */ if (pool_prime(&ecb_pool, 1) == ENOMEM) { printf("WARNING: not enough memory for ncr53c9x_ecb\n"); } ecb_pool_initialized = 1; } if (sc->sc_state == 0) { /* First time through; initialize. */ TAILQ_INIT(&sc->ready_list); sc->sc_nexus = NULL; memset(sc->sc_tinfo, 0, sizeof(*sc->sc_tinfo)); for (r = 0; r < sc->sc_ntarg; r++) { LIST_INIT(&sc->sc_tinfo[r].luns); } } else { ncr53c9x_clear(sc, XS_TIMEOUT); } /* * reset the chip to a known state */ ncr53c9x_reset(sc); sc->sc_flags = 0; sc->sc_msgpriq = sc->sc_msgout = sc->sc_msgoutq = 0; sc->sc_phase = sc->sc_prevphase = INVALID_PHASE; /* XXXSMP scsipi */ KERNEL_LOCK(1, curlwp); for (r = 0; r < sc->sc_ntarg; r++) { struct ncr53c9x_tinfo *ti = &sc->sc_tinfo[r]; /* XXX - config flags per target: low bits: no reselect; high bits: no synch */ ti->flags = ((sc->sc_minsync && !(sc->sc_cfflags & (1 << ((r & 7) + 8)))) ? 0 : T_SYNCHOFF) | ((sc->sc_cfflags & (1 << (r & 7))) ? T_RSELECTOFF : 0); #ifdef DEBUG if (ncr53c9x_notag) ti->flags &= ~T_TAG; #endif ti->period = sc->sc_minsync; ti->offset = 0; ti->cfg3 = 0; ncr53c9x_update_xfer_mode(sc, r); } if (doreset) { sc->sc_state = NCR_SBR; NCRCMD(sc, NCRCMD_RSTSCSI); /* Notify upper layer */ scsipi_async_event(&sc->sc_channel, ASYNC_EVENT_RESET, NULL); } else { sc->sc_state = NCR_IDLE; ncr53c9x_sched(sc); } /* XXXSMP scsipi */ KERNEL_UNLOCK_ONE(curlwp); } /* * Read the NCR registers, and save their contents for later use. * NCR_STAT, NCR_STEP & NCR_INTR are mostly zeroed out when reading * NCR_INTR - so make sure it is the last read. * * I think that (from reading the docs) most bits in these registers * only make sense when he DMA CSR has an interrupt showing. Call only * if an interrupt is pending. */ inline void ncr53c9x_readregs(struct ncr53c9x_softc *sc) { sc->sc_espstat = NCR_READ_REG(sc, NCR_STAT); /* Only the stepo bits are of interest */ sc->sc_espstep = NCR_READ_REG(sc, NCR_STEP) & NCRSTEP_MASK; if (sc->sc_rev == NCR_VARIANT_FAS366) sc->sc_espstat2 = NCR_READ_REG(sc, NCR_STAT2); sc->sc_espintr = NCR_READ_REG(sc, NCR_INTR); if (sc->sc_glue->gl_clear_latched_intr != NULL) (*sc->sc_glue->gl_clear_latched_intr)(sc); /* * Determine the SCSI bus phase, return either a real SCSI bus phase * or some pseudo phase we use to detect certain exceptions. */ sc->sc_phase = (sc->sc_espintr & NCRINTR_DIS) ? /* Disconnected */ BUSFREE_PHASE : sc->sc_espstat & NCRSTAT_PHASE; NCR_INTS(("regs[intr=%02x,stat=%02x,step=%02x,stat2=%02x] ", sc->sc_espintr, sc->sc_espstat, sc->sc_espstep, sc->sc_espstat2)); } /* * Convert Synchronous Transfer Period to chip register Clock Per Byte value. */ static inline int ncr53c9x_stp2cpb(struct ncr53c9x_softc *sc, int period) { int v; v = (sc->sc_freq * period) / 250; if (ncr53c9x_cpb2stp(sc, v) < period) /* Correct round-down error */ v++; return v; } static inline void ncr53c9x_setsync(struct ncr53c9x_softc *sc, struct ncr53c9x_tinfo *ti) { uint8_t syncoff, synctp; uint8_t cfg3 = sc->sc_cfg3 | ti->cfg3; if (ti->flags & T_SYNCMODE) { syncoff = ti->offset; synctp = ncr53c9x_stp2cpb(sc, ti->period); if (sc->sc_features & NCR_F_FASTSCSI) { /* * If the period is 200ns or less (ti->period <= 50), * put the chip in Fast SCSI mode. */ if (ti->period <= 50) /* * There are (at least) 4 variations of the * configuration 3 register. The drive attach * routine sets the appropriate bit to put the * chip into Fast SCSI mode so that it doesn't * have to be figured out here each time. */ cfg3 |= sc->sc_cfg3_fscsi; } /* * Am53c974 requires different SYNCTP values when the * FSCSI bit is off. */ if (sc->sc_rev == NCR_VARIANT_AM53C974 && (cfg3 & NCRAMDCFG3_FSCSI) == 0) synctp--; } else { syncoff = 0; synctp = 0; } if (sc->sc_features & NCR_F_HASCFG3) NCR_WRITE_REG(sc, NCR_CFG3, cfg3); NCR_WRITE_REG(sc, NCR_SYNCOFF, syncoff); NCR_WRITE_REG(sc, NCR_SYNCTP, synctp); } /* * Send a command to a target, set the driver state to NCR_SELECTING * and let the caller take care of the rest. * * Keeping this as a function allows me to say that this may be done * by DMA instead of programmed I/O soon. */ void ncr53c9x_select(struct ncr53c9x_softc *sc, struct ncr53c9x_ecb *ecb) { struct scsipi_periph *periph = ecb->xs->xs_periph; int target = periph->periph_target; int lun = periph->periph_lun; struct ncr53c9x_tinfo *ti = &sc->sc_tinfo[target]; int tiflags = ti->flags; uint8_t *cmd; int clen; bool selatn3, selatns; size_t dmasize; NCR_TRACE(("[ncr53c9x_select(t%d,l%d,cmd:%x,tag:%x,%x)] ", target, lun, ecb->cmd.cmd.opcode, ecb->tag[0], ecb->tag[1])); sc->sc_state = NCR_SELECTING; /* * Schedule the timeout now, the first time we will go away * expecting to come back due to an interrupt, because it is * always possible that the interrupt may never happen. */ if ((ecb->xs->xs_control & XS_CTL_POLL) == 0) { callout_reset(&ecb->xs->xs_callout, mstohz(ecb->timeout), ncr53c9x_timeout, ecb); } /* * The docs say the target register is never reset, and I * can't think of a better place to set it */ if (sc->sc_rev == NCR_VARIANT_FAS366) { NCRCMD(sc, NCRCMD_FLUSH); NCR_WRITE_REG(sc, NCR_SELID, target | NCR_BUSID_HME); } else { NCR_WRITE_REG(sc, NCR_SELID, target); } ncr53c9x_setsync(sc, ti); if ((ecb->flags & ECB_SENSE) != 0) { /* * For REQUEST SENSE, we should not send an IDENTIFY or * otherwise mangle the target. There should be no MESSAGE IN * phase. */ if (sc->sc_features & NCR_F_DMASELECT) { /* setup DMA transfer for command */ dmasize = clen = ecb->clen; sc->sc_cmdlen = clen; sc->sc_cmdp = (void *)&ecb->cmd.cmd; NCRDMA_SETUP(sc, &sc->sc_cmdp, &sc->sc_cmdlen, 0, &dmasize); /* Program the SCSI counter */ NCR_SET_COUNT(sc, dmasize); if (sc->sc_rev != NCR_VARIANT_FAS366) NCRCMD(sc, NCRCMD_NOP | NCRCMD_DMA); /* And get the targets attention */ NCRCMD(sc, NCRCMD_SELNATN | NCRCMD_DMA); NCRDMA_GO(sc); } else { ncr53c9x_wrfifo(sc, (uint8_t *)&ecb->cmd.cmd, ecb->clen); sc->sc_cmdlen = 0; NCRCMD(sc, NCRCMD_SELNATN); } return; } selatn3 = selatns = false; if (ecb->tag[0] != 0) { if (sc->sc_features & NCR_F_SELATN3) /* use SELATN3 to send tag messages */ selatn3 = true; else /* We don't have SELATN3; use SELATNS to send tags */ selatns = true; } if (ti->flags & T_NEGOTIATE) { /* We have to use SELATNS to send sync/wide messages */ selatn3 = false; selatns = true; } cmd = (uint8_t *)&ecb->cmd.cmd; if (selatn3) { /* We'll use tags with SELATN3 */ clen = ecb->clen + 3; cmd -= 3; cmd[0] = MSG_IDENTIFY(lun, 1); /* msg[0] */ cmd[1] = ecb->tag[0]; /* msg[1] */ cmd[2] = ecb->tag[1]; /* msg[2] */ } else { /* We don't have tags, or will send messages with SELATNS */ clen = ecb->clen + 1; cmd -= 1; cmd[0] = MSG_IDENTIFY(lun, (tiflags & T_RSELECTOFF) == 0); } if ((sc->sc_features & NCR_F_DMASELECT) && !selatns) { /* setup DMA transfer for command */ dmasize = clen; sc->sc_cmdlen = clen; sc->sc_cmdp = cmd; NCRDMA_SETUP(sc, &sc->sc_cmdp, &sc->sc_cmdlen, 0, &dmasize); /* Program the SCSI counter */ NCR_SET_COUNT(sc, dmasize); /* load the count in */ /* if (sc->sc_rev != NCR_VARIANT_FAS366) */ NCRCMD(sc, NCRCMD_NOP | NCRCMD_DMA); /* And get the targets attention */ if (selatn3) { sc->sc_msgout = SEND_TAG; sc->sc_flags |= NCR_ATN; NCRCMD(sc, NCRCMD_SELATN3 | NCRCMD_DMA); } else NCRCMD(sc, NCRCMD_SELATN | NCRCMD_DMA); NCRDMA_GO(sc); return; } /* * Who am I. This is where we tell the target that we are * happy for it to disconnect etc. */ /* Now get the command into the FIFO */ sc->sc_cmdlen = 0; ncr53c9x_wrfifo(sc, cmd, clen); /* And get the targets attention */ if (selatns) { NCR_MSGS(("SELATNS \n")); /* Arbitrate, select and stop after IDENTIFY message */ NCRCMD(sc, NCRCMD_SELATNS); } else if (selatn3) { sc->sc_msgout = SEND_TAG; sc->sc_flags |= NCR_ATN; NCRCMD(sc, NCRCMD_SELATN3); } else NCRCMD(sc, NCRCMD_SELATN); } void ncr53c9x_free_ecb(struct ncr53c9x_softc *sc, struct ncr53c9x_ecb *ecb) { int s; s = splbio(); ecb->flags = 0; pool_put(&ecb_pool, (void *)ecb); splx(s); return; } struct ncr53c9x_ecb * ncr53c9x_get_ecb(struct ncr53c9x_softc *sc, int flags) { struct ncr53c9x_ecb *ecb; int s; s = splbio(); ecb = pool_get(&ecb_pool, PR_NOWAIT); splx(s); if (ecb) { memset(ecb, 0, sizeof(*ecb)); ecb->flags |= ECB_ALLOC; } return ecb; } /* * DRIVER FUNCTIONS CALLABLE FROM HIGHER LEVEL DRIVERS */ /* * Start a SCSI-command * This function is called by the higher level SCSI-driver to queue/run * SCSI-commands. */ void ncr53c9x_scsipi_request(struct scsipi_channel *chan, scsipi_adapter_req_t req, void *arg) { struct scsipi_xfer *xs; struct scsipi_periph *periph; struct ncr53c9x_softc *sc; struct ncr53c9x_ecb *ecb; int flags; NCR_TRACE(("[ncr53c9x_scsipi_request] ")); sc = device_private(chan->chan_adapter->adapt_dev); mutex_enter(&sc->sc_lock); switch (req) { case ADAPTER_REQ_RUN_XFER: xs = arg; periph = xs->xs_periph; flags = xs->xs_control; NCR_CMDS(("[0x%x, %d]->%d ", (int)xs->cmd->opcode, xs->cmdlen, periph->periph_target)); /* Get an ECB to use. */ ecb = ncr53c9x_get_ecb(sc, xs->xs_control); /* * This should never happen as we track resources * in the mid-layer, but for now it can as pool_get() * can fail. */ if (ecb == NULL) { scsipi_printaddr(periph); printf("%s: unable to allocate ecb\n", device_xname(sc->sc_dev)); xs->error = XS_RESOURCE_SHORTAGE; mutex_exit(&sc->sc_lock); scsipi_done(xs); return; } /* Initialize ecb */ ecb->xs = xs; ecb->timeout = xs->timeout; if (flags & XS_CTL_RESET) { ecb->flags |= ECB_RESET; ecb->clen = 0; ecb->dleft = 0; } else { memcpy(&ecb->cmd.cmd, xs->cmd, xs->cmdlen); ecb->clen = xs->cmdlen; ecb->daddr = xs->data; ecb->dleft = xs->datalen; } ecb->stat = 0; TAILQ_INSERT_TAIL(&sc->ready_list, ecb, chain); ecb->flags |= ECB_READY; if (sc->sc_state == NCR_IDLE) ncr53c9x_sched(sc); if ((flags & XS_CTL_POLL) == 0) break; /* Not allowed to use interrupts, use polling instead */ if (ncr53c9x_poll(sc, xs, ecb->timeout)) { ncr53c9x_timeout(ecb); if (ncr53c9x_poll(sc, xs, ecb->timeout)) ncr53c9x_timeout(ecb); } break; case ADAPTER_REQ_GROW_RESOURCES: /* XXX Not supported. */ break; case ADAPTER_REQ_SET_XFER_MODE: { struct ncr53c9x_tinfo *ti; struct scsipi_xfer_mode *xm = arg; ti = &sc->sc_tinfo[xm->xm_target]; ti->flags &= ~(T_NEGOTIATE|T_SYNCMODE); ti->period = 0; ti->offset = 0; if ((sc->sc_cfflags & (1 << ((xm->xm_target & 7) + 16))) == 0 && (xm->xm_mode & PERIPH_CAP_TQING)) { NCR_MISC(("%s: target %d: tagged queuing\n", device_xname(sc->sc_dev), xm->xm_target)); ti->flags |= T_TAG; } else ti->flags &= ~T_TAG; if ((xm->xm_mode & PERIPH_CAP_WIDE16) != 0) { NCR_MISC(("%s: target %d: wide scsi negotiation\n", device_xname(sc->sc_dev), xm->xm_target)); if (sc->sc_rev == NCR_VARIANT_FAS366) { ti->flags |= T_WIDE; ti->width = 1; } } if ((xm->xm_mode & PERIPH_CAP_SYNC) != 0 && (ti->flags & T_SYNCHOFF) == 0 && sc->sc_minsync != 0) { NCR_MISC(("%s: target %d: sync negotiation\n", device_xname(sc->sc_dev), xm->xm_target)); ti->flags |= T_NEGOTIATE; ti->period = sc->sc_minsync; } /* * If we're not going to negotiate, send the notification * now, since it won't happen later. */ if ((ti->flags & T_NEGOTIATE) == 0) ncr53c9x_update_xfer_mode(sc, xm->xm_target); } break; } mutex_exit(&sc->sc_lock); } void ncr53c9x_update_xfer_mode(struct ncr53c9x_softc *sc, int target) { struct scsipi_xfer_mode xm; struct ncr53c9x_tinfo *ti = &sc->sc_tinfo[target]; xm.xm_target = target; xm.xm_mode = 0; xm.xm_period = 0; xm.xm_offset = 0; if (ti->flags & T_SYNCMODE) { xm.xm_mode |= PERIPH_CAP_SYNC; xm.xm_period = ti->period; xm.xm_offset = ti->offset; } if (ti->width) xm.xm_mode |= PERIPH_CAP_WIDE16; if ((ti->flags & (T_RSELECTOFF|T_TAG)) == T_TAG) xm.xm_mode |= PERIPH_CAP_TQING; scsipi_async_event(&sc->sc_channel, ASYNC_EVENT_XFER_MODE, &xm); } /* * Used when interrupt driven I/O isn't allowed, e.g. during boot. */ int ncr53c9x_poll(struct ncr53c9x_softc *sc, struct scsipi_xfer *xs, int count) { NCR_TRACE(("[ncr53c9x_poll] ")); while (count) { if (NCRDMA_ISINTR(sc)) { mutex_exit(&sc->sc_lock); ncr53c9x_intr(sc); mutex_enter(&sc->sc_lock); } #if alternatively if (NCR_READ_REG(sc, NCR_STAT) & NCRSTAT_INT) ncr53c9x_intr(sc); #endif if ((xs->xs_status & XS_STS_DONE) != 0) return 0; if (sc->sc_state == NCR_IDLE) { NCR_TRACE(("[ncr53c9x_poll: rescheduling] ")); ncr53c9x_sched(sc); } DELAY(1000); count--; } return 1; } int ncr53c9x_ioctl(struct scsipi_channel *chan, u_long cmd, void *arg, int flag, struct proc *p) { struct ncr53c9x_softc *sc; int error = 0; sc = device_private(chan->chan_adapter->adapt_dev); switch (cmd) { case SCBUSIORESET: mutex_enter(&sc->sc_lock); ncr53c9x_init(sc, 1); mutex_exit(&sc->sc_lock); break; default: error = ENOTTY; break; } return error; } /* * LOW LEVEL SCSI UTILITIES */ /* * Schedule a scsi operation. This has now been pulled out of the interrupt * handler so that we may call it from ncr53c9x_scsipi_request and * ncr53c9x_done. This may save us an unnecessary interrupt just to get * things going. Should only be called when state == NCR_IDLE and at bio pl. */ void ncr53c9x_sched(struct ncr53c9x_softc *sc) { struct ncr53c9x_ecb *ecb; struct scsipi_periph *periph; struct ncr53c9x_tinfo *ti; struct ncr53c9x_linfo *li; int lun; int tag; NCR_TRACE(("[ncr53c9x_sched] ")); if (sc->sc_state != NCR_IDLE) panic("%s: not IDLE (state=%d)", __func__, sc->sc_state); /* * Find first ecb in ready queue that is for a target/lunit * combinations that is not busy. */ for (ecb = TAILQ_FIRST(&sc->ready_list); ecb != NULL; ecb = TAILQ_NEXT(ecb, chain)) { periph = ecb->xs->xs_periph; ti = &sc->sc_tinfo[periph->periph_target]; lun = periph->periph_lun; /* Select type of tag for this command */ if ((ti->flags & T_RSELECTOFF) != 0) tag = 0; else if ((ti->flags & T_TAG) == 0) tag = 0; else if ((ecb->flags & ECB_SENSE) != 0) tag = 0; else tag = ecb->xs->xs_tag_type; #if 0 /* XXXX Use tags for polled commands? */ if (ecb->xs->xs_control & XS_CTL_POLL) tag = 0; #endif li = TINFO_LUN(ti, lun); if (li == NULL) { /* Initialize LUN info and add to list. */ li = malloc(sizeof(*li), M_DEVBUF, M_NOWAIT|M_ZERO); if (li == NULL) { continue; } li->lun = lun; LIST_INSERT_HEAD(&ti->luns, li, link); if (lun < NCR_NLUN) ti->lun[lun] = li; } li->last_used = time_second; if (tag == 0) { /* Try to issue this as an un-tagged command */ if (li->untagged == NULL) li->untagged = ecb; } if (li->untagged != NULL) { tag = 0; if ((li->busy != 1) && li->used == 0) { /* We need to issue this untagged command now */ ecb = li->untagged; periph = ecb->xs->xs_periph; } else { /* Not ready yet */ continue; } } ecb->tag[0] = tag; if (tag != 0) { li->queued[ecb->xs->xs_tag_id] = ecb; ecb->tag[1] = ecb->xs->xs_tag_id; li->used++; } if (li->untagged != NULL && (li->busy != 1)) { li->busy = 1; TAILQ_REMOVE(&sc->ready_list, ecb, chain); ecb->flags &= ~ECB_READY; sc->sc_nexus = ecb; ncr53c9x_select(sc, ecb); break; } if (li->untagged == NULL && tag != 0) { TAILQ_REMOVE(&sc->ready_list, ecb, chain); ecb->flags &= ~ECB_READY; sc->sc_nexus = ecb; ncr53c9x_select(sc, ecb); break; } else { NCR_TRACE(("%d:%d busy\n", periph->periph_target, periph->periph_lun)); } } } void ncr53c9x_sense(struct ncr53c9x_softc *sc, struct ncr53c9x_ecb *ecb) { struct scsipi_xfer *xs = ecb->xs; struct scsipi_periph *periph = xs->xs_periph; struct ncr53c9x_tinfo *ti = &sc->sc_tinfo[periph->periph_target]; struct scsi_request_sense *ss = (void *)&ecb->cmd.cmd; struct ncr53c9x_linfo *li; int lun = periph->periph_lun; NCR_TRACE(("requesting sense ")); /* Next, setup a request sense command block */ memset(ss, 0, sizeof(*ss)); ss->opcode = SCSI_REQUEST_SENSE; ss->byte2 = periph->periph_lun << SCSI_CMD_LUN_SHIFT; ss->length = sizeof(struct scsi_sense_data); ecb->clen = sizeof(*ss); ecb->daddr = (uint8_t *)&xs->sense.scsi_sense; ecb->dleft = sizeof(struct scsi_sense_data); ecb->flags |= ECB_SENSE; ecb->timeout = NCR_SENSE_TIMEOUT; ti->senses++; li = TINFO_LUN(ti, lun); if (li->busy) li->busy = 0; ncr53c9x_dequeue(sc, ecb); li->untagged = ecb; /* must be executed first to fix C/A */ li->busy = 2; if (ecb == sc->sc_nexus) { ncr53c9x_select(sc, ecb); } else { TAILQ_INSERT_HEAD(&sc->ready_list, ecb, chain); ecb->flags |= ECB_READY; if (sc->sc_state == NCR_IDLE) ncr53c9x_sched(sc); } } /* * POST PROCESSING OF SCSI_CMD (usually current) */ void ncr53c9x_done(struct ncr53c9x_softc *sc, struct ncr53c9x_ecb *ecb) { struct scsipi_xfer *xs = ecb->xs; struct scsipi_periph *periph = xs->xs_periph; struct ncr53c9x_tinfo *ti = &sc->sc_tinfo[periph->periph_target]; int lun = periph->periph_lun; struct ncr53c9x_linfo *li = TINFO_LUN(ti, lun); NCR_TRACE(("[ncr53c9x_done(error:%x)] ", xs->error)); if ((xs->xs_control & XS_CTL_POLL) == 0) callout_stop(&xs->xs_callout); /* * Now, if we've come here with no error code, i.e. we've kept the * initial XS_NOERROR, and the status code signals that we should * check sense, we'll need to set up a request sense cmd block and * push the command back into the ready queue *before* any other * commands for this target/lunit, else we lose the sense info. * We don't support chk sense conditions for the request sense cmd. */ if (xs->error == XS_NOERROR) { xs->status = ecb->stat; if ((ecb->flags & ECB_ABORT) != 0) { xs->error = XS_TIMEOUT; } else if ((ecb->flags & ECB_SENSE) != 0) { xs->error = XS_SENSE; } else if ((ecb->stat & ST_MASK) == SCSI_CHECK) { /* First, save the return values */ xs->resid = ecb->dleft; ncr53c9x_sense(sc, ecb); return; } else { xs->resid = ecb->dleft; } if (xs->status == SCSI_QUEUE_FULL || xs->status == XS_BUSY) xs->error = XS_BUSY; } #ifdef NCR53C9X_DEBUG if (ncr53c9x_debug & NCR_SHOWTRAC) { if (xs->resid != 0) printf("resid=%d ", xs->resid); if (xs->error == XS_SENSE) printf("sense=0x%02x\n", xs->sense.scsi_sense.response_code); else printf("error=%d\n", xs->error); } #endif /* * Remove the ECB from whatever queue it's on. */ ncr53c9x_dequeue(sc, ecb); if (ecb == sc->sc_nexus) { sc->sc_nexus = NULL; if (sc->sc_state != NCR_CLEANING) { sc->sc_state = NCR_IDLE; ncr53c9x_sched(sc); } } if (xs->error == XS_SELTIMEOUT) { /* Selection timeout -- discard this LUN if empty */ if (li->untagged == NULL && li->used == 0) { if (lun < NCR_NLUN) ti->lun[lun] = NULL; LIST_REMOVE(li, link); free(li, M_DEVBUF); } } ncr53c9x_free_ecb(sc, ecb); ti->cmds++; mutex_exit(&sc->sc_lock); scsipi_done(xs); mutex_enter(&sc->sc_lock); } void ncr53c9x_dequeue(struct ncr53c9x_softc *sc, struct ncr53c9x_ecb *ecb) { struct ncr53c9x_tinfo *ti = &sc->sc_tinfo[ecb->xs->xs_periph->periph_target]; struct ncr53c9x_linfo *li; int64_t lun = ecb->xs->xs_periph->periph_lun; li = TINFO_LUN(ti, lun); #ifdef DIAGNOSTIC if (li == NULL || li->lun != lun) panic("%s: lun %" PRIx64 " for ecb %p does not exist", __func__, lun, ecb); #endif if (li->untagged == ecb) { li->busy = 0; li->untagged = NULL; } if (ecb->tag[0] && li->queued[ecb->tag[1]] != NULL) { #ifdef DIAGNOSTIC if (li->queued[ecb->tag[1]] != NULL && (li->queued[ecb->tag[1]] != ecb)) panic("%s: slot %d for lun %" PRIx64 " has %p " "instead of ecb %p\n", __func__, ecb->tag[1], lun, li->queued[ecb->tag[1]], ecb); #endif li->queued[ecb->tag[1]] = NULL; li->used--; } if ((ecb->flags & ECB_READY) != 0) { ecb->flags &= ~ECB_READY; TAILQ_REMOVE(&sc->ready_list, ecb, chain); } } /* * INTERRUPT/PROTOCOL ENGINE */ /* * Schedule an outgoing message by prioritizing it, and asserting * attention on the bus. We can only do this when we are the initiator * else there will be an illegal command interrupt. */ #define ncr53c9x_sched_msgout(m) \ do { \ NCR_MSGS(("ncr53c9x_sched_msgout %x %d", m, __LINE__)); \ NCRCMD(sc, NCRCMD_SETATN); \ sc->sc_flags |= NCR_ATN; \ sc->sc_msgpriq |= (m); \ } while (/* CONSTCOND */0) static void ncr53c9x_flushfifo(struct ncr53c9x_softc *sc) { NCR_TRACE(("[flushfifo] ")); NCRCMD(sc, NCRCMD_FLUSH); if (sc->sc_phase == COMMAND_PHASE || sc->sc_phase == MESSAGE_OUT_PHASE) DELAY(2); } static int ncr53c9x_rdfifo(struct ncr53c9x_softc *sc, int how) { int i, n; uint8_t *ibuf; switch (how) { case NCR_RDFIFO_START: ibuf = sc->sc_imess; sc->sc_imlen = 0; break; case NCR_RDFIFO_CONTINUE: ibuf = sc->sc_imess + sc->sc_imlen; break; default: panic("%s: bad flag", __func__); break; } /* * XXX buffer (sc_imess) size for message */ n = NCR_READ_REG(sc, NCR_FFLAG) & NCRFIFO_FF; if (sc->sc_rev == NCR_VARIANT_FAS366) { n *= 2; for (i = 0; i < n; i++) ibuf[i] = NCR_READ_REG(sc, NCR_FIFO); if (sc->sc_espstat2 & NCRFAS_STAT2_ISHUTTLE) { NCR_WRITE_REG(sc, NCR_FIFO, 0); ibuf[i++] = NCR_READ_REG(sc, NCR_FIFO); NCR_READ_REG(sc, NCR_FIFO); ncr53c9x_flushfifo(sc); } } else { for (i = 0; i < n; i++) ibuf[i] = NCR_READ_REG(sc, NCR_FIFO); } sc->sc_imlen += i; #if 0 #ifdef NCR53C9X_DEBUG { int j; NCR_TRACE(("\n[rdfifo %s (%d):", (how == NCR_RDFIFO_START) ? "start" : "cont", (int)sc->sc_imlen)); if (ncr53c9x_debug & NCR_SHOWTRAC) { for (j = 0; j < sc->sc_imlen; j++) printf(" %02x", sc->sc_imess[j]); printf("]\n"); } } #endif #endif return sc->sc_imlen; } static void ncr53c9x_wrfifo(struct ncr53c9x_softc *sc, uint8_t *p, int len) { int i; #ifdef NCR53C9X_DEBUG NCR_MSGS(("[wrfifo(%d):", len)); if (ncr53c9x_debug & NCR_SHOWMSGS) { for (i = 0; i < len; i++) printf(" %02x", p[i]); printf("]\n"); } #endif for (i = 0; i < len; i++) { NCR_WRITE_REG(sc, NCR_FIFO, p[i]); if (sc->sc_rev == NCR_VARIANT_FAS366) NCR_WRITE_REG(sc, NCR_FIFO, 0); } } int ncr53c9x_reselect(struct ncr53c9x_softc *sc, int message, int tagtype, int tagid) { uint8_t selid, target, lun; struct ncr53c9x_ecb *ecb = NULL; struct ncr53c9x_tinfo *ti; struct ncr53c9x_linfo *li; if (sc->sc_rev == NCR_VARIANT_FAS366) { target = sc->sc_selid; } else { /* * The SCSI chip made a snapshot of the data bus * while the reselection was being negotiated. * This enables us to determine which target did * the reselect. */ selid = sc->sc_selid & ~(1 << sc->sc_id); if (selid & (selid - 1)) { printf("%s: reselect with invalid selid %02x;" " sending DEVICE RESET\n", device_xname(sc->sc_dev), selid); goto reset; } target = ffs(selid) - 1; } lun = message & 0x07; /* * Search wait queue for disconnected cmd * The list should be short, so I haven't bothered with * any more sophisticated structures than a simple * singly linked list. */ ti = &sc->sc_tinfo[target]; li = TINFO_LUN(ti, lun); /* * We can get as far as the LUN with the IDENTIFY * message. Check to see if we're running an * un-tagged command. Otherwise ack the IDENTIFY * and wait for a tag message. */ if (li != NULL) { if (li->untagged != NULL && li->busy) ecb = li->untagged; else if (tagtype != MSG_SIMPLE_Q_TAG) { /* Wait for tag to come by */ sc->sc_state = NCR_IDENTIFIED; return 0; } else if (tagtype) ecb = li->queued[tagid]; } if (ecb == NULL) { printf("%s: reselect from target %d lun %d tag %x:%x " "with no nexus; sending ABORT\n", device_xname(sc->sc_dev), target, lun, tagtype, tagid); goto abort; } /* Make this nexus active again. */ sc->sc_state = NCR_CONNECTED; sc->sc_nexus = ecb; ncr53c9x_setsync(sc, ti); if (ecb->flags & ECB_RESET) ncr53c9x_sched_msgout(SEND_DEV_RESET); else if (ecb->flags & ECB_ABORT) ncr53c9x_sched_msgout(SEND_ABORT); /* Do an implicit RESTORE POINTERS. */ sc->sc_dp = ecb->daddr; sc->sc_dleft = ecb->dleft; return 0; reset: ncr53c9x_sched_msgout(SEND_DEV_RESET); return 1; abort: ncr53c9x_sched_msgout(SEND_ABORT); return 1; } static inline int __verify_msg_format(uint8_t *p, int len) { if (len == 1 && MSG_IS1BYTE(p[0])) return 1; if (len == 2 && MSG_IS2BYTE(p[0])) return 1; if (len >= 3 && MSG_ISEXTENDED(p[0]) && len == p[1] + 2) return 1; return 0; } /* * Get an incoming message as initiator. * * The SCSI bus must already be in MESSAGE_IN_PHASE and there is a * byte in the FIFO */ void ncr53c9x_msgin(struct ncr53c9x_softc *sc) { NCR_TRACE(("[ncr53c9x_msgin(curmsglen:%ld)] ", (long)sc->sc_imlen)); if (sc->sc_imlen == 0) { printf("%s: msgin: no msg byte available\n", device_xname(sc->sc_dev)); return; } /* * Prepare for a new message. A message should (according * to the SCSI standard) be transmitted in one single * MESSAGE_IN_PHASE. If we have been in some other phase, * then this is a new message. */ if (sc->sc_prevphase != MESSAGE_IN_PHASE && sc->sc_state != NCR_RESELECTED) { printf("%s: phase change, dropping message, " "prev %d, state %d\n", device_xname(sc->sc_dev), sc->sc_prevphase, sc->sc_state); sc->sc_flags &= ~NCR_DROP_MSGI; sc->sc_imlen = 0; } /* * If we're going to reject the message, don't bother storing * the incoming bytes. But still, we need to ACK them. */ if ((sc->sc_flags & NCR_DROP_MSGI) != 0) { NCRCMD(sc, NCRCMD_MSGOK); printf("", sc->sc_imess[sc->sc_imlen]); return; } if (sc->sc_imlen >= NCR_MAX_MSG_LEN) { ncr53c9x_sched_msgout(SEND_REJECT); sc->sc_flags |= NCR_DROP_MSGI; } else { uint8_t *pb; int plen; switch (sc->sc_state) { /* * if received message is the first of reselection * then first byte is selid, and then message */ case NCR_RESELECTED: pb = sc->sc_imess + 1; plen = sc->sc_imlen - 1; break; default: pb = sc->sc_imess; plen = sc->sc_imlen; break; } if (__verify_msg_format(pb, plen)) goto gotit; } /* Ack what we have so far */ NCRCMD(sc, NCRCMD_MSGOK); return; gotit: NCR_MSGS(("gotmsg(%x) state %d", sc->sc_imess[0], sc->sc_state)); /* we got complete message, flush the imess, */ /* XXX nobody uses imlen below */ sc->sc_imlen = 0; /* * Now we should have a complete message (1 byte, 2 byte * and moderately long extended messages). We only handle * extended messages which total length is shorter than * NCR_MAX_MSG_LEN. Longer messages will be amputated. */ switch (sc->sc_state) { struct ncr53c9x_ecb *ecb; struct ncr53c9x_tinfo *ti; struct ncr53c9x_linfo *li; int lun; case NCR_CONNECTED: ecb = sc->sc_nexus; ti = &sc->sc_tinfo[ecb->xs->xs_periph->periph_target]; switch (sc->sc_imess[0]) { case MSG_CMDCOMPLETE: NCR_MSGS(("cmdcomplete ")); if (sc->sc_dleft < 0) { scsipi_printaddr(ecb->xs->xs_periph); printf("%s: got %ld extra bytes\n", device_xname(sc->sc_dev), -(long)sc->sc_dleft); sc->sc_dleft = 0; } ecb->dleft = (ecb->flags & ECB_TENTATIVE_DONE) ? 0 : sc->sc_dleft; if ((ecb->flags & ECB_SENSE) == 0) ecb->xs->resid = ecb->dleft; sc->sc_state = NCR_CMDCOMPLETE; break; case MSG_MESSAGE_REJECT: NCR_MSGS(("msg reject (msgout=%x) ", sc->sc_msgout)); switch (sc->sc_msgout) { case SEND_TAG: /* * Target does not like tagged queuing. * - Flush the command queue * - Disable tagged queuing for the target * - Dequeue ecb from the queued array. */ printf("%s: tagged queuing rejected: " "target %d\n", device_xname(sc->sc_dev), ecb->xs->xs_periph->periph_target); NCR_MSGS(("(rejected sent tag)")); NCRCMD(sc, NCRCMD_FLUSH); DELAY(1); ti->flags &= ~T_TAG; lun = ecb->xs->xs_periph->periph_lun; li = TINFO_LUN(ti, lun); if (ecb->tag[0] && li->queued[ecb->tag[1]] != NULL) { li->queued[ecb->tag[1]] = NULL; li->used--; } ecb->tag[0] = ecb->tag[1] = 0; li->untagged = ecb; li->busy = 1; break; case SEND_SDTR: printf("%s: sync transfer rejected: " "target %d\n", device_xname(sc->sc_dev), ecb->xs->xs_periph->periph_target); sc->sc_flags &= ~NCR_SYNCHNEGO; ti->flags &= ~(T_NEGOTIATE | T_SYNCMODE); ncr53c9x_setsync(sc, ti); ncr53c9x_update_xfer_mode(sc, ecb->xs->xs_periph->periph_target); break; case SEND_WDTR: printf("%s: wide transfer rejected: " "target %d\n", device_xname(sc->sc_dev), ecb->xs->xs_periph->periph_target); ti->flags &= ~(T_WIDE | T_WDTRSENT); ti->width = 0; break; case SEND_INIT_DET_ERR: goto abort; } break; case MSG_NOOP: NCR_MSGS(("noop ")); break; case MSG_HEAD_OF_Q_TAG: case MSG_SIMPLE_Q_TAG: case MSG_ORDERED_Q_TAG: NCR_MSGS(("TAG %x:%x", sc->sc_imess[0], sc->sc_imess[1])); break; case MSG_DISCONNECT: NCR_MSGS(("disconnect ")); ti->dconns++; sc->sc_state = NCR_DISCONNECT; /* * Mark the fact that all bytes have moved. The * target may not bother to do a SAVE POINTERS * at this stage. This flag will set the residual * count to zero on MSG COMPLETE. */ if (sc->sc_dleft == 0) ecb->flags |= ECB_TENTATIVE_DONE; break; case MSG_SAVEDATAPOINTER: NCR_MSGS(("save datapointer ")); ecb->daddr = sc->sc_dp; ecb->dleft = sc->sc_dleft; break; case MSG_RESTOREPOINTERS: NCR_MSGS(("restore datapointer ")); sc->sc_dp = ecb->daddr; sc->sc_dleft = ecb->dleft; break; case MSG_EXTENDED: NCR_MSGS(("extended(%x) ", sc->sc_imess[2])); switch (sc->sc_imess[2]) { case MSG_EXT_SDTR: NCR_MSGS(("SDTR period %d, offset %d ", sc->sc_imess[3], sc->sc_imess[4])); if (sc->sc_imess[1] != 3) goto reject; ti->period = sc->sc_imess[3]; ti->offset = sc->sc_imess[4]; ti->flags &= ~T_NEGOTIATE; if (sc->sc_minsync == 0 || ti->offset == 0 || ti->period > 124) { #if 0 #ifdef NCR53C9X_DEBUG scsipi_printaddr(ecb->xs->xs_periph); printf("async mode\n"); #endif #endif ti->flags &= ~T_SYNCMODE; if ((sc->sc_flags&NCR_SYNCHNEGO) == 0) { /* * target initiated negotiation */ ti->offset = 0; ncr53c9x_sched_msgout( SEND_SDTR); } } else { int p; p = ncr53c9x_stp2cpb(sc, ti->period); ti->period = ncr53c9x_cpb2stp(sc, p); if ((sc->sc_flags&NCR_SYNCHNEGO) == 0) { /* * target initiated negotiation */ if (ti->period < sc->sc_minsync) ti->period = sc->sc_minsync; if (ti->offset > 15) ti->offset = 15; ti->flags &= ~T_SYNCMODE; ncr53c9x_sched_msgout( SEND_SDTR); } else { /* we are sync */ ti->flags |= T_SYNCMODE; } } ncr53c9x_update_xfer_mode(sc, ecb->xs->xs_periph->periph_target); sc->sc_flags &= ~NCR_SYNCHNEGO; ncr53c9x_setsync(sc, ti); break; case MSG_EXT_WDTR: #ifdef NCR53C9X_DEBUG printf("%s: wide mode %d\n", device_xname(sc->sc_dev), sc->sc_imess[3]); #endif if (sc->sc_imess[3] == 1) { ti->cfg3 |= NCRFASCFG3_EWIDE; ncr53c9x_setsync(sc, ti); } else ti->width = 0; /* * Device started width negotiation. */ if ((ti->flags & T_WDTRSENT) == 0) ncr53c9x_sched_msgout(SEND_WDTR); ti->flags &= ~(T_WIDE | T_WDTRSENT); break; default: scsipi_printaddr(ecb->xs->xs_periph); printf("%s: unrecognized MESSAGE EXTENDED;" " sending REJECT\n", device_xname(sc->sc_dev)); goto reject; } break; default: NCR_MSGS(("ident ")); scsipi_printaddr(ecb->xs->xs_periph); printf("%s: unrecognized MESSAGE; sending REJECT\n", device_xname(sc->sc_dev)); reject: ncr53c9x_sched_msgout(SEND_REJECT); break; } break; case NCR_IDENTIFIED: /* * IDENTIFY message was received and queue tag is expected now */ if ((sc->sc_imess[0] != MSG_SIMPLE_Q_TAG) || (sc->sc_msgify == 0)) { printf("%s: TAG reselect without IDENTIFY;" " MSG %x;" " sending DEVICE RESET\n", device_xname(sc->sc_dev), sc->sc_imess[0]); goto reset; } (void)ncr53c9x_reselect(sc, sc->sc_msgify, sc->sc_imess[0], sc->sc_imess[1]); break; case NCR_RESELECTED: if (MSG_ISIDENTIFY(sc->sc_imess[1])) { sc->sc_msgify = sc->sc_imess[1]; } else { printf("%s: reselect without IDENTIFY;" " MSG %x;" " sending DEVICE RESET\n", device_xname(sc->sc_dev), sc->sc_imess[1]); goto reset; } (void)ncr53c9x_reselect(sc, sc->sc_msgify, 0, 0); break; default: printf("%s: unexpected MESSAGE IN; sending DEVICE RESET\n", device_xname(sc->sc_dev)); reset: ncr53c9x_sched_msgout(SEND_DEV_RESET); break; abort: ncr53c9x_sched_msgout(SEND_ABORT); break; } /* if we have more messages to send set ATN */ if (sc->sc_msgpriq) NCRCMD(sc, NCRCMD_SETATN); /* Ack last message byte */ NCRCMD(sc, NCRCMD_MSGOK); /* Done, reset message pointer. */ sc->sc_flags &= ~NCR_DROP_MSGI; sc->sc_imlen = 0; } /* * Send the highest priority, scheduled message */ void ncr53c9x_msgout(struct ncr53c9x_softc *sc) { struct ncr53c9x_tinfo *ti; struct ncr53c9x_ecb *ecb; size_t size; NCR_TRACE(("[ncr53c9x_msgout(priq:%x, prevphase:%x)]", sc->sc_msgpriq, sc->sc_prevphase)); /* * XXX - the NCR_ATN flag is not in sync with the actual ATN * condition on the SCSI bus. The 53c9x chip * automatically turns off ATN before sending the * message byte. (see also the comment below in the * default case when picking out a message to send) */ if (sc->sc_flags & NCR_ATN) { if (sc->sc_prevphase != MESSAGE_OUT_PHASE) { new: NCRCMD(sc, NCRCMD_FLUSH); #if 0 DELAY(1); #endif sc->sc_msgoutq = 0; sc->sc_omlen = 0; } } else { if (sc->sc_prevphase == MESSAGE_OUT_PHASE) { ncr53c9x_sched_msgout(sc->sc_msgoutq); goto new; } else { printf("%s at line %d: unexpected MESSAGE OUT phase\n", device_xname(sc->sc_dev), __LINE__); } } if (sc->sc_omlen == 0) { /* Pick up highest priority message */ sc->sc_msgout = sc->sc_msgpriq & -sc->sc_msgpriq; sc->sc_msgoutq |= sc->sc_msgout; sc->sc_msgpriq &= ~sc->sc_msgout; sc->sc_omlen = 1; /* "Default" message len */ switch (sc->sc_msgout) { case SEND_SDTR: ecb = sc->sc_nexus; ti = &sc->sc_tinfo[ecb->xs->xs_periph->periph_target]; sc->sc_omess[0] = MSG_EXTENDED; sc->sc_omess[1] = MSG_EXT_SDTR_LEN; sc->sc_omess[2] = MSG_EXT_SDTR; sc->sc_omess[3] = ti->period; sc->sc_omess[4] = ti->offset; sc->sc_omlen = 5; if ((sc->sc_flags & NCR_SYNCHNEGO) == 0) { ti->flags |= T_SYNCMODE; ncr53c9x_setsync(sc, ti); } break; case SEND_WDTR: ecb = sc->sc_nexus; ti = &sc->sc_tinfo[ecb->xs->xs_periph->periph_target]; sc->sc_omess[0] = MSG_EXTENDED; sc->sc_omess[1] = MSG_EXT_WDTR_LEN; sc->sc_omess[2] = MSG_EXT_WDTR; sc->sc_omess[3] = ti->width; sc->sc_omlen = 4; break; case SEND_IDENTIFY: if (sc->sc_state != NCR_CONNECTED) { printf("%s at line %d: no nexus\n", device_xname(sc->sc_dev), __LINE__); } ecb = sc->sc_nexus; sc->sc_omess[0] = MSG_IDENTIFY(ecb->xs->xs_periph->periph_lun, 0); break; case SEND_TAG: if (sc->sc_state != NCR_CONNECTED) { printf("%s at line %d: no nexus\n", device_xname(sc->sc_dev), __LINE__); } ecb = sc->sc_nexus; sc->sc_omess[0] = ecb->tag[0]; sc->sc_omess[1] = ecb->tag[1]; sc->sc_omlen = 2; break; case SEND_DEV_RESET: sc->sc_flags |= NCR_ABORTING; sc->sc_omess[0] = MSG_BUS_DEV_RESET; ecb = sc->sc_nexus; ti = &sc->sc_tinfo[ecb->xs->xs_periph->periph_target]; ti->flags &= ~T_SYNCMODE; ncr53c9x_update_xfer_mode(sc, ecb->xs->xs_periph->periph_target); if ((ti->flags & T_SYNCHOFF) == 0) /* We can re-start sync negotiation */ ti->flags |= T_NEGOTIATE; break; case SEND_PARITY_ERROR: sc->sc_omess[0] = MSG_PARITY_ERROR; break; case SEND_ABORT: sc->sc_flags |= NCR_ABORTING; sc->sc_omess[0] = MSG_ABORT; break; case SEND_INIT_DET_ERR: sc->sc_omess[0] = MSG_INITIATOR_DET_ERR; break; case SEND_REJECT: sc->sc_omess[0] = MSG_MESSAGE_REJECT; break; default: /* * We normally do not get here, since the chip * automatically turns off ATN before the last * byte of a message is sent to the target. * However, if the target rejects our (multi-byte) * message early by switching to MSG IN phase * ATN remains on, so the target may return to * MSG OUT phase. If there are no scheduled messages * left we send a NO-OP. * * XXX - Note that this leaves no useful purpose for * the NCR_ATN flag. */ sc->sc_flags &= ~NCR_ATN; sc->sc_omess[0] = MSG_NOOP; break; } sc->sc_omp = sc->sc_omess; } #ifdef DEBUG if (ncr53c9x_debug & NCR_SHOWMSGS) { int i; NCR_MSGS(("sc_omlen; i++) NCR_MSGS((" %02x", sc->sc_omess[i])); NCR_MSGS(("> ")); } #endif if (sc->sc_rev == NCR_VARIANT_FAS366) { /* * XXX fifo size */ ncr53c9x_flushfifo(sc); ncr53c9x_wrfifo(sc, sc->sc_omp, sc->sc_omlen); sc->sc_cmdlen = 0; NCRCMD(sc, NCRCMD_TRANS); } else { /* (re)send the message */ size = min(sc->sc_omlen, sc->sc_maxxfer); NCRDMA_SETUP(sc, &sc->sc_omp, &sc->sc_omlen, 0, &size); /* Program the SCSI counter */ NCR_SET_COUNT(sc, size); /* Load the count in and start the message-out transfer */ NCRCMD(sc, NCRCMD_NOP | NCRCMD_DMA); NCRCMD(sc, NCRCMD_TRANS | NCRCMD_DMA); NCRDMA_GO(sc); } } /* * This is the most critical part of the driver, and has to know * how to deal with *all* error conditions and phases from the SCSI * bus. If there are no errors and the DMA was active, then call the * DMA pseudo-interrupt handler. If this returns 1, then that was it * and we can return from here without further processing. * * Most of this needs verifying. */ int ncr53c9x_intr(void *arg) { struct ncr53c9x_softc *sc = arg; struct ncr53c9x_ecb *ecb; struct scsipi_periph *periph; struct ncr53c9x_tinfo *ti; size_t size; int nfifo; NCR_INTS(("[ncr53c9x_intr: state %d]", sc->sc_state)); if (!NCRDMA_ISINTR(sc)) return 0; mutex_enter(&sc->sc_lock); again: /* and what do the registers say... */ ncr53c9x_readregs(sc); sc->sc_intrcnt.ev_count++; /* * At the moment, only a SCSI Bus Reset or Illegal * Command are classed as errors. A disconnect is a * valid condition, and we let the code check is the * "NCR_BUSFREE_OK" flag was set before declaring it * and error. * * Also, the status register tells us about "Gross * Errors" and "Parity errors". Only the Gross Error * is really bad, and the parity errors are dealt * with later * * TODO * If there are too many parity error, go to slow * cable mode ? */ /* SCSI Reset */ if ((sc->sc_espintr & NCRINTR_SBR) != 0) { if ((NCR_READ_REG(sc, NCR_FFLAG) & NCRFIFO_FF) != 0) { NCRCMD(sc, NCRCMD_FLUSH); DELAY(1); } if (sc->sc_state != NCR_SBR) { printf("%s: SCSI bus reset\n", device_xname(sc->sc_dev)); ncr53c9x_init(sc, 0); /* Restart everything */ goto out; } #if 0 /*XXX*/ printf("\n", sc->sc_espintr, sc->sc_espstat, sc->sc_espstep); #endif if (sc->sc_nexus != NULL) panic("%s: nexus in reset state", device_xname(sc->sc_dev)); goto sched; } ecb = sc->sc_nexus; #define NCRINTR_ERR (NCRINTR_SBR|NCRINTR_ILL) if (sc->sc_espintr & NCRINTR_ERR || sc->sc_espstat & NCRSTAT_GE) { if ((sc->sc_espstat & NCRSTAT_GE) != 0) { /* Gross Error; no target ? */ if (NCR_READ_REG(sc, NCR_FFLAG) & NCRFIFO_FF) { NCRCMD(sc, NCRCMD_FLUSH); DELAY(1); } if (sc->sc_state == NCR_CONNECTED || sc->sc_state == NCR_SELECTING) { ecb->xs->error = XS_TIMEOUT; ncr53c9x_done(sc, ecb); } goto out; } if ((sc->sc_espintr & NCRINTR_ILL) != 0) { if ((sc->sc_flags & NCR_EXPECT_ILLCMD) != 0) { /* * Eat away "Illegal command" interrupt * on a ESP100 caused by a re-selection * while we were trying to select * another target. */ #ifdef NCR53C9X_DEBUG printf("%s: ESP100 work-around activated\n", device_xname(sc->sc_dev)); #endif sc->sc_flags &= ~NCR_EXPECT_ILLCMD; goto out; } /* illegal command, out of sync ? */ printf("%s: illegal command: 0x%x " "(state %d, phase %x, prevphase %x)\n", device_xname(sc->sc_dev), sc->sc_lastcmd, sc->sc_state, sc->sc_phase, sc->sc_prevphase); if (NCR_READ_REG(sc, NCR_FFLAG) & NCRFIFO_FF) { NCRCMD(sc, NCRCMD_FLUSH); DELAY(1); } ncr53c9x_init(sc, 1); /* Restart everything */ goto out; } } sc->sc_flags &= ~NCR_EXPECT_ILLCMD; /* * Call if DMA is active. * * If DMA_INTR returns true, then maybe go 'round the loop * again in case there is no more DMA queued, but a phase * change is expected. */ if (NCRDMA_ISACTIVE(sc)) { int r = NCRDMA_INTR(sc); if (r == -1) { printf("%s: DMA error; resetting\n", device_xname(sc->sc_dev)); ncr53c9x_init(sc, 1); goto out; } /* If DMA active here, then go back to work... */ if (NCRDMA_ISACTIVE(sc)) goto out; if ((sc->sc_espstat & NCRSTAT_TC) == 0) { /* * DMA not completed. If we can not find a * acceptable explanation, print a diagnostic. */ if (sc->sc_state == NCR_SELECTING) /* * This can happen if we are reselected * while using DMA to select a target. */ /*void*/; else if (sc->sc_prevphase == MESSAGE_OUT_PHASE) { /* * Our (multi-byte) message (eg SDTR) was * interrupted by the target to send * a MSG REJECT. * Print diagnostic if current phase * is not MESSAGE IN. */ if (sc->sc_phase != MESSAGE_IN_PHASE) printf("%s: !TC on MSG OUT" " [intr %x, stat %x, step %d]" " prevphase %x, resid %lx\n", device_xname(sc->sc_dev), sc->sc_espintr, sc->sc_espstat, sc->sc_espstep, sc->sc_prevphase, (u_long)sc->sc_omlen); } else if (sc->sc_dleft == 0) { /* * The DMA operation was started for * a DATA transfer. Print a diagnostic * if the DMA counter and TC bit * appear to be out of sync. */ printf("%s: !TC on DATA XFER" " [intr %x, stat %x, step %d]" " prevphase %x, resid %x\n", device_xname(sc->sc_dev), sc->sc_espintr, sc->sc_espstat, sc->sc_espstep, sc->sc_prevphase, ecb ? ecb->dleft : -1); } } } /* * Check for less serious errors. */ if ((sc->sc_espstat & NCRSTAT_PE) != 0) { printf("%s: SCSI bus parity error\n", device_xname(sc->sc_dev)); if (sc->sc_prevphase == MESSAGE_IN_PHASE) ncr53c9x_sched_msgout(SEND_PARITY_ERROR); else ncr53c9x_sched_msgout(SEND_INIT_DET_ERR); } if ((sc->sc_espintr & NCRINTR_DIS) != 0) { sc->sc_msgify = 0; NCR_INTS(("", sc->sc_espintr,sc->sc_espstat,sc->sc_espstep)); if (NCR_READ_REG(sc, NCR_FFLAG) & NCRFIFO_FF) { NCRCMD(sc, NCRCMD_FLUSH); #if 0 DELAY(1); #endif } /* * This command must (apparently) be issued within * 250mS of a disconnect. So here you are... */ NCRCMD(sc, NCRCMD_ENSEL); switch (sc->sc_state) { case NCR_RESELECTED: goto sched; case NCR_SELECTING: { struct ncr53c9x_linfo *li; ecb->xs->error = XS_SELTIMEOUT; /* Selection timeout -- discard all LUNs if empty */ periph = ecb->xs->xs_periph; ti = &sc->sc_tinfo[periph->periph_target]; li = LIST_FIRST(&ti->luns); while (li != NULL) { if (li->untagged == NULL && li->used == 0) { if (li->lun < NCR_NLUN) ti->lun[li->lun] = NULL; LIST_REMOVE(li, link); free(li, M_DEVBUF); /* * Restart the search at the beginning */ li = LIST_FIRST(&ti->luns); continue; } li = LIST_NEXT(li, link); } goto finish; } case NCR_CONNECTED: if ((sc->sc_flags & NCR_SYNCHNEGO) != 0) { #ifdef NCR53C9X_DEBUG if (ecb != NULL) scsipi_printaddr(ecb->xs->xs_periph); printf("sync nego not completed!\n"); #endif ti = &sc->sc_tinfo[ ecb->xs->xs_periph->periph_target]; sc->sc_flags &= ~NCR_SYNCHNEGO; ti->flags &= ~(T_NEGOTIATE | T_SYNCMODE); } /* it may be OK to disconnect */ if ((sc->sc_flags & NCR_ABORTING) == 0) { /* * Section 5.1.1 of the SCSI 2 spec * suggests issuing a REQUEST SENSE * following an unexpected disconnect. * Some devices go into a contingent * allegiance condition when * disconnecting, and this is necessary * to clean up their state. */ printf("%s: unexpected disconnect " "[state %d, intr %x, stat %x, phase(c %x, p %x)]; ", device_xname(sc->sc_dev), sc->sc_state, sc->sc_espintr, sc->sc_espstat, sc->sc_phase, sc->sc_prevphase); if ((ecb->flags & ECB_SENSE) != 0) { printf("resetting\n"); goto reset; } printf("sending REQUEST SENSE\n"); callout_stop(&ecb->xs->xs_callout); ncr53c9x_sense(sc, ecb); goto out; } ecb->xs->error = XS_TIMEOUT; goto finish; case NCR_DISCONNECT: sc->sc_nexus = NULL; goto sched; case NCR_CMDCOMPLETE: goto finish; } } switch (sc->sc_state) { case NCR_SBR: printf("%s: waiting for SCSI Bus Reset to happen\n", device_xname(sc->sc_dev)); goto out; case NCR_RESELECTED: /* * we must be continuing a message ? */ printf("%s: unhandled reselect continuation, " "state %d, intr %02x\n", device_xname(sc->sc_dev), sc->sc_state, sc->sc_espintr); ncr53c9x_init(sc, 1); goto out; case NCR_IDENTIFIED: ecb = sc->sc_nexus; if (sc->sc_phase != MESSAGE_IN_PHASE) { int i = (NCR_READ_REG(sc, NCR_FFLAG) & NCRFIFO_FF); /* * Things are seriously screwed up. * Pull the brakes, i.e. reset */ printf("%s: target didn't send tag: %d bytes in fifo\n", device_xname(sc->sc_dev), i); /* Drain and display fifo */ while (i-- > 0) printf("[%d] ", NCR_READ_REG(sc, NCR_FIFO)); ncr53c9x_init(sc, 1); goto out; } else goto msgin; case NCR_IDLE: case NCR_SELECTING: ecb = sc->sc_nexus; if (sc->sc_espintr & NCRINTR_RESEL) { sc->sc_msgpriq = sc->sc_msgout = sc->sc_msgoutq = 0; sc->sc_flags = 0; /* * If we're trying to select a * target ourselves, push our command * back into the ready list. */ if (sc->sc_state == NCR_SELECTING) { NCR_INTS(("backoff selector ")); callout_stop(&ecb->xs->xs_callout); ncr53c9x_dequeue(sc, ecb); TAILQ_INSERT_HEAD(&sc->ready_list, ecb, chain); ecb->flags |= ECB_READY; ecb = sc->sc_nexus = NULL; } sc->sc_state = NCR_RESELECTED; if (sc->sc_phase != MESSAGE_IN_PHASE) { /* * Things are seriously screwed up. * Pull the brakes, i.e. reset */ printf("%s: target didn't identify\n", device_xname(sc->sc_dev)); ncr53c9x_init(sc, 1); goto out; } /* * The C90 only inhibits FIFO writes until reselection * is complete, instead of waiting until the interrupt * status register has been read. So, if the reselect * happens while we were entering command bytes (for * another target) some of those bytes can appear in * the FIFO here, after the interrupt is taken. * * To remedy this situation, pull the Selection ID * and Identify message from the FIFO directly, and * ignore any extraneous fifo contents. Also, set * a flag that allows one Illegal Command Interrupt * to occur which the chip also generates as a result * of writing to the FIFO during a reselect. */ if (sc->sc_rev == NCR_VARIANT_ESP100) { nfifo = NCR_READ_REG(sc, NCR_FFLAG) & NCRFIFO_FF; sc->sc_imess[0] = NCR_READ_REG(sc, NCR_FIFO); sc->sc_imess[1] = NCR_READ_REG(sc, NCR_FIFO); sc->sc_imlen = 2; if (nfifo != 2) { /* Flush the rest */ NCRCMD(sc, NCRCMD_FLUSH); } sc->sc_flags |= NCR_EXPECT_ILLCMD; if (nfifo > 2) nfifo = 2; /* We fixed it.. */ } else nfifo = ncr53c9x_rdfifo(sc, NCR_RDFIFO_START); if (nfifo != 2) { printf("%s: RESELECT: %d bytes in FIFO! " "[intr %x, stat %x, step %d, " "prevphase %x]\n", device_xname(sc->sc_dev), nfifo, sc->sc_espintr, sc->sc_espstat, sc->sc_espstep, sc->sc_prevphase); ncr53c9x_init(sc, 1); goto out; } sc->sc_selid = sc->sc_imess[0]; NCR_INTS(("selid=%02x ", sc->sc_selid)); /* Handle identify message */ ncr53c9x_msgin(sc); if (sc->sc_state != NCR_CONNECTED && sc->sc_state != NCR_IDENTIFIED) { /* IDENTIFY fail?! */ printf("%s: identify failed, " "state %d, intr %02x\n", device_xname(sc->sc_dev), sc->sc_state, sc->sc_espintr); ncr53c9x_init(sc, 1); goto out; } goto shortcut; /* ie. next phase expected soon */ } #define NCRINTR_DONE (NCRINTR_FC | NCRINTR_BS) if ((sc->sc_espintr & NCRINTR_DONE) == NCRINTR_DONE) { /* * Arbitration won; examine the `step' register * to determine how far the selection could progress. */ ecb = sc->sc_nexus; if (ecb == NULL) panic("%s: no nexus", __func__); periph = ecb->xs->xs_periph; ti = &sc->sc_tinfo[periph->periph_target]; switch (sc->sc_espstep) { case 0: /* * The target did not respond with a * message out phase - probably an old * device that doesn't recognize ATN. * Clear ATN and just continue, the * target should be in the command * phase. * XXXX check for command phase? */ NCRCMD(sc, NCRCMD_RSTATN); break; case 1: if ((ti->flags & T_NEGOTIATE) == 0 && ecb->tag[0] == 0) { printf("%s: step 1 & !NEG\n", device_xname(sc->sc_dev)); goto reset; } if (sc->sc_phase != MESSAGE_OUT_PHASE) { printf("%s: !MSGOUT\n", device_xname(sc->sc_dev)); goto reset; } if (ti->flags & T_WIDE) { ti->flags |= T_WDTRSENT; ncr53c9x_sched_msgout(SEND_WDTR); } if (ti->flags & T_NEGOTIATE) { /* Start negotiating */ ti->period = sc->sc_minsync; ti->offset = 15; sc->sc_flags |= NCR_SYNCHNEGO; if (ecb->tag[0]) ncr53c9x_sched_msgout( SEND_TAG | SEND_SDTR); else ncr53c9x_sched_msgout( SEND_SDTR); } else { /* Could not do ATN3 so send TAG */ ncr53c9x_sched_msgout(SEND_TAG); } sc->sc_prevphase = MESSAGE_OUT_PHASE; /* XXXX */ break; case 3: /* * Grr, this is supposed to mean * "target left command phase prematurely". * It seems to happen regularly when * sync mode is on. * Look at FIFO to see if command went out. * (Timing problems?) */ if (sc->sc_features & NCR_F_DMASELECT) { if (sc->sc_cmdlen == 0) /* Hope for the best.. */ break; } else if ((NCR_READ_REG(sc, NCR_FFLAG) & NCRFIFO_FF) == 0) { /* Hope for the best.. */ break; } printf("(%s:%d:%d): selection failed;" " %d left in FIFO " "[intr %x, stat %x, step %d]\n", device_xname(sc->sc_dev), periph->periph_target, periph->periph_lun, NCR_READ_REG(sc, NCR_FFLAG) & NCRFIFO_FF, sc->sc_espintr, sc->sc_espstat, sc->sc_espstep); NCRCMD(sc, NCRCMD_FLUSH); ncr53c9x_sched_msgout(SEND_ABORT); goto out; case 2: /* Select stuck at Command Phase */ NCRCMD(sc, NCRCMD_FLUSH); break; case 4: if (sc->sc_features & NCR_F_DMASELECT && sc->sc_cmdlen != 0) printf("(%s:%d:%d): select; " "%lu left in DMA buffer " "[intr %x, stat %x, step %d]\n", device_xname(sc->sc_dev), periph->periph_target, periph->periph_lun, (u_long)sc->sc_cmdlen, sc->sc_espintr, sc->sc_espstat, sc->sc_espstep); /* So far, everything went fine */ break; } sc->sc_prevphase = INVALID_PHASE; /* ?? */ /* Do an implicit RESTORE POINTERS. */ sc->sc_dp = ecb->daddr; sc->sc_dleft = ecb->dleft; sc->sc_state = NCR_CONNECTED; break; } else { printf("%s: unexpected status after select" ": [intr %x, stat %x, step %x]\n", device_xname(sc->sc_dev), sc->sc_espintr, sc->sc_espstat, sc->sc_espstep); NCRCMD(sc, NCRCMD_FLUSH); DELAY(1); goto reset; } if (sc->sc_state == NCR_IDLE) { printf("%s: stray interrupt\n", device_xname(sc->sc_dev)); mutex_exit(&sc->sc_lock); return 0; } break; case NCR_CONNECTED: if ((sc->sc_flags & NCR_ICCS) != 0) { /* "Initiate Command Complete Steps" in progress */ uint8_t msg; sc->sc_flags &= ~NCR_ICCS; if ((sc->sc_espintr & NCRINTR_DONE) == 0) { printf("%s: ICCS: " ": [intr %x, stat %x, step %x]\n", device_xname(sc->sc_dev), sc->sc_espintr, sc->sc_espstat, sc->sc_espstep); } ncr53c9x_rdfifo(sc, NCR_RDFIFO_START); if (sc->sc_imlen < 2) printf("%s: can't get status, only %d bytes\n", device_xname(sc->sc_dev), (int)sc->sc_imlen); ecb->stat = sc->sc_imess[sc->sc_imlen - 2]; msg = sc->sc_imess[sc->sc_imlen - 1]; NCR_PHASE(("", ecb->stat, msg)); if (msg == MSG_CMDCOMPLETE) { ecb->dleft = (ecb->flags & ECB_TENTATIVE_DONE) ? 0 : sc->sc_dleft; if ((ecb->flags & ECB_SENSE) == 0) ecb->xs->resid = ecb->dleft; sc->sc_state = NCR_CMDCOMPLETE; } else printf("%s: STATUS_PHASE: msg %d\n", device_xname(sc->sc_dev), msg); sc->sc_imlen = 0; NCRCMD(sc, NCRCMD_MSGOK); goto shortcut; /* ie. wait for disconnect */ } break; default: printf("%s: invalid state: %d [intr %x, phase(c %x, p %x)]\n", device_xname(sc->sc_dev), sc->sc_state, sc->sc_espintr, sc->sc_phase, sc->sc_prevphase); goto reset; } /* * Driver is now in state NCR_CONNECTED, i.e. we * have a current command working the SCSI bus. */ if (sc->sc_state != NCR_CONNECTED || ecb == NULL) { panic("%s: no nexus", __func__); } switch (sc->sc_phase) { case MESSAGE_OUT_PHASE: NCR_PHASE(("MESSAGE_OUT_PHASE ")); ncr53c9x_msgout(sc); sc->sc_prevphase = MESSAGE_OUT_PHASE; break; case MESSAGE_IN_PHASE: msgin: NCR_PHASE(("MESSAGE_IN_PHASE ")); if ((sc->sc_espintr & NCRINTR_BS) != 0) { if ((sc->sc_rev != NCR_VARIANT_FAS366) || (sc->sc_espstat2 & NCRFAS_STAT2_EMPTY) == 0) { NCRCMD(sc, NCRCMD_FLUSH); } sc->sc_flags |= NCR_WAITI; NCRCMD(sc, NCRCMD_TRANS); } else if ((sc->sc_espintr & NCRINTR_FC) != 0) { if ((sc->sc_flags & NCR_WAITI) == 0) { printf("%s: MSGIN: unexpected FC bit: " "[intr %x, stat %x, step %x]\n", device_xname(sc->sc_dev), sc->sc_espintr, sc->sc_espstat, sc->sc_espstep); } sc->sc_flags &= ~NCR_WAITI; ncr53c9x_rdfifo(sc, (sc->sc_prevphase == sc->sc_phase) ? NCR_RDFIFO_CONTINUE : NCR_RDFIFO_START); ncr53c9x_msgin(sc); } else { printf("%s: MSGIN: weird bits: " "[intr %x, stat %x, step %x]\n", device_xname(sc->sc_dev), sc->sc_espintr, sc->sc_espstat, sc->sc_espstep); } sc->sc_prevphase = MESSAGE_IN_PHASE; goto shortcut; /* i.e. expect data to be ready */ case COMMAND_PHASE: /* * Send the command block. Normally we don't see this * phase because the SEL_ATN command takes care of * all this. However, we end up here if either the * target or we wanted to exchange some more messages * first (e.g. to start negotiations). */ NCR_PHASE(("COMMAND_PHASE 0x%02x (%d) ", ecb->cmd.cmd.opcode, ecb->clen)); if (NCR_READ_REG(sc, NCR_FFLAG) & NCRFIFO_FF) { NCRCMD(sc, NCRCMD_FLUSH); #if 0 DELAY(1); #endif } if (sc->sc_features & NCR_F_DMASELECT) { /* setup DMA transfer for command */ size = ecb->clen; sc->sc_cmdlen = size; sc->sc_cmdp = (void *)&ecb->cmd.cmd; NCRDMA_SETUP(sc, &sc->sc_cmdp, &sc->sc_cmdlen, 0, &size); /* Program the SCSI counter */ NCR_SET_COUNT(sc, size); /* load the count in */ NCRCMD(sc, NCRCMD_NOP | NCRCMD_DMA); /* start the command transfer */ NCRCMD(sc, NCRCMD_TRANS | NCRCMD_DMA); NCRDMA_GO(sc); } else { ncr53c9x_wrfifo(sc, (uint8_t *)&ecb->cmd.cmd, ecb->clen); sc->sc_cmdlen = 0; NCRCMD(sc, NCRCMD_TRANS); } sc->sc_prevphase = COMMAND_PHASE; break; case DATA_OUT_PHASE: NCR_PHASE(("DATA_OUT_PHASE [%ld] ",(long)sc->sc_dleft)); NCRCMD(sc, NCRCMD_FLUSH); size = min(sc->sc_dleft, sc->sc_maxxfer); NCRDMA_SETUP(sc, &sc->sc_dp, &sc->sc_dleft, 0, &size); sc->sc_prevphase = DATA_OUT_PHASE; goto setup_xfer; case DATA_IN_PHASE: NCR_PHASE(("DATA_IN_PHASE ")); if (sc->sc_rev == NCR_VARIANT_ESP100) NCRCMD(sc, NCRCMD_FLUSH); size = min(sc->sc_dleft, sc->sc_maxxfer); NCRDMA_SETUP(sc, &sc->sc_dp, &sc->sc_dleft, 1, &size); sc->sc_prevphase = DATA_IN_PHASE; setup_xfer: /* Target returned to data phase: wipe "done" memory */ ecb->flags &= ~ECB_TENTATIVE_DONE; /* Program the SCSI counter */ NCR_SET_COUNT(sc, size); /* load the count in */ NCRCMD(sc, NCRCMD_NOP | NCRCMD_DMA); /* * Note that if `size' is 0, we've already transceived * all the bytes we want but we're still in DATA PHASE. * Apparently, the device needs padding. Also, a * transfer size of 0 means "maximum" to the chip * DMA logic. */ NCRCMD(sc, (size == 0 ? NCRCMD_TRPAD : NCRCMD_TRANS) | NCRCMD_DMA); NCRDMA_GO(sc); goto out; case STATUS_PHASE: NCR_PHASE(("STATUS_PHASE ")); sc->sc_flags |= NCR_ICCS; NCRCMD(sc, NCRCMD_ICCS); sc->sc_prevphase = STATUS_PHASE; goto shortcut; /* i.e. expect status results soon */ case INVALID_PHASE: break; default: printf("%s: unexpected bus phase; resetting\n", device_xname(sc->sc_dev)); goto reset; } out: mutex_exit(&sc->sc_lock); return 1; reset: ncr53c9x_init(sc, 1); goto out; finish: ncr53c9x_done(sc, ecb); goto out; sched: sc->sc_state = NCR_IDLE; ncr53c9x_sched(sc); goto out; shortcut: /* * The idea is that many of the SCSI operations take very little * time, and going away and getting interrupted is too high an * overhead to pay. For example, selecting, sending a message * and command and then doing some work can be done in one "pass". * * The delay is a heuristic. It is 2 when at 20MHz, 2 at 25MHz and 1 * at 40MHz. This needs testing. */ { struct timeval wait, cur; microtime(&wait); wait.tv_usec += 50 / sc->sc_freq; if (wait.tv_usec > 1000000) { wait.tv_sec++; wait.tv_usec -= 1000000; } do { if (NCRDMA_ISINTR(sc)) goto again; microtime(&cur); } while (timercmp(&cur, &wait, <=)); } goto out; } void ncr53c9x_abort(struct ncr53c9x_softc *sc, struct ncr53c9x_ecb *ecb) { /* 2 secs for the abort */ ecb->timeout = NCR_ABORT_TIMEOUT; ecb->flags |= ECB_ABORT; if (ecb == sc->sc_nexus) { /* * If we're still selecting, the message will be scheduled * after selection is complete. */ if (sc->sc_state == NCR_CONNECTED) ncr53c9x_sched_msgout(SEND_ABORT); /* * Reschedule timeout. */ callout_reset(&ecb->xs->xs_callout, mstohz(ecb->timeout), ncr53c9x_timeout, ecb); } else { /* * Just leave the command where it is. * XXX - what choice do we have but to reset the SCSI * eventually? */ if (sc->sc_state == NCR_IDLE) ncr53c9x_sched(sc); } } void ncr53c9x_timeout(void *arg) { struct ncr53c9x_ecb *ecb = arg; struct scsipi_xfer *xs = ecb->xs; struct scsipi_periph *periph = xs->xs_periph; struct ncr53c9x_softc *sc; struct ncr53c9x_tinfo *ti; sc = device_private(periph->periph_channel->chan_adapter->adapt_dev); ti = &sc->sc_tinfo[periph->periph_target]; scsipi_printaddr(periph); printf("%s: timed out [ecb %p (flags 0x%x, dleft %x, stat %x)], " "", device_xname(sc->sc_dev), ecb, ecb->flags, ecb->dleft, ecb->stat, sc->sc_state, sc->sc_nexus, NCR_READ_REG(sc, NCR_STAT), sc->sc_phase, sc->sc_prevphase, (long)sc->sc_dleft, sc->sc_msgpriq, sc->sc_msgout, NCRDMA_ISACTIVE(sc) ? "DMA active" : ""); #if NCR53C9X_DEBUG > 1 printf("TRACE: %s.", ecb->trace); #endif mutex_enter(&sc->sc_lock); if (ecb->flags & ECB_ABORT) { /* abort timed out */ printf(" AGAIN\n"); ncr53c9x_init(sc, 1); } else { /* abort the operation that has timed out */ printf("\n"); xs->error = XS_TIMEOUT; ncr53c9x_abort(sc, ecb); /* Disable sync mode if stuck in a data phase */ if (ecb == sc->sc_nexus && (ti->flags & T_SYNCMODE) != 0 && (sc->sc_phase & (MSGI | CDI)) == 0) { /* XXX ASYNC CALLBACK! */ scsipi_printaddr(periph); printf("sync negotiation disabled\n"); sc->sc_cfflags |= (1 << ((periph->periph_target & 7) + 8)); ncr53c9x_update_xfer_mode(sc, periph->periph_target); } } mutex_exit(&sc->sc_lock); } void ncr53c9x_watch(void *arg) { struct ncr53c9x_softc *sc = arg; struct ncr53c9x_tinfo *ti; struct ncr53c9x_linfo *li; int t; /* Delete any structures that have not been used in 10min. */ time_t old = time_second - (10 * 60); mutex_enter(&sc->sc_lock); for (t = 0; t < sc->sc_ntarg; t++) { ti = &sc->sc_tinfo[t]; li = LIST_FIRST(&ti->luns); while (li) { if (li->last_used < old && li->untagged == NULL && li->used == 0) { if (li->lun < NCR_NLUN) ti->lun[li->lun] = NULL; LIST_REMOVE(li, link); free(li, M_DEVBUF); /* Restart the search at the beginning */ li = LIST_FIRST(&ti->luns); continue; } li = LIST_NEXT(li, link); } } mutex_exit(&sc->sc_lock); callout_reset(&sc->sc_watchdog, 60 * hz, ncr53c9x_watch, sc); }