/* $NetBSD: upcreg.h,v 1.3 2003/03/02 00:21:47 bjh21 Exp $ */ /* * Ben Harris, 2000, 2003 * * This file is in the public domain. */ /* * upcreg.h - CHIPS and Technologies Universal Peripheral Controllers */ /* * This file contains register details for: * CHIPS 82C710 Universal Peripheral Controller * CHIPS 82C711 Universal Peripheral Controller II * CHIPS 82C721 Universal Peripheral Controller III */ #define UPC_BUS_SIZE 0x400 /* Approximate */ /* Fixed port addresses */ #define UPC_PORT_IDECMDBASE 0x1f0 /* IDE primary base */ #define UPC_PORT_IDECTLBASE 0x3f6 /* IDE secondary base */ #define UPC_PORT_FDCBASE 0x3f4 /* FDC base address (82C721 only) */ #define UPC_PORT_GAME 0x201 /* -GAMECS active */ /* 82C710 Configuration magic sequences */ #define UPC1_PORT_CFG1 0x2fa /* First magic config register */ #define UPC1_PORT_CFG2 0x3fa /* Second magic config register */ #define UPC1_CFGMAGIC_1 0x55 /* First magic number */ #define UPC1_CFGMAGIC_2 0xaa /* Second magic number */ #define UPC1_CFGMAGIC_3 0x36 /* Third magic number */ /* 82C710 configuration registers */ #define UPC1_CFGADDR_CR0 0x00 #define UPC1_CFGADDR_CR1 0x01 #define UPC1_CFGADDR_CR2 0x02 #define UPC1_CFGADDR_UARTBASE 0x04 #define UPC1_CFGADDR_PARBASE 0x06 #define UPC1_CFGADDR_GPCSBASE 0x09 #define UPC1_CFGADDR_CRA 0x0a #define UPC1_CFGADDR_CRB 0x0b #define UPC1_CFGADDR_CRC 0x0c #define UPC1_CFGADDR_MOUSEBASE 0x0d #define UPC1_CFGADDR_CRE 0x0e #define UPC1_CFGADDR_CONFBASE 0x0f #define UPC1_CFGADDR_EXIT 0x0f /* 82C710 configuration register 0x00 */ #define UPC1_CR0_VALID 0x80 /* Device has been configured */ #define UPC1_CR0_OSC_MASK 0x60 /* Oscillator control */ #define UPC1_CR0_OSC_ON 0x00 /* Oscillator always on */ #define UPC1_CR0_OSC_PWRGD 0x20 /* Oscillator on when PWRGD */ #define UPC1_CR0_OSC_OFF 0x60 /* Oscillator always off */ #define UPC1_CR0_PEN 0x08 /* Enable parallel port */ #define UPC1_CR0_SEN 0x04 /* Enable UART */ /* 82C710 configuration register 0x01 */ #define UPC1_CR1_RESET 0x80 /* Reset ignores serial port */ #define UPC1_CR1_PRBI 0x40 /* Bi-directional printer support */ #define UPC1_CR1_FCTS 0x20 /* Force UART CTS* active */ #define UPC1_CR1_FDSR 0x10 /* Force UART DSR* active */ #define UPC1_CR1_FDCD 0x08 /* Force UART DCD* active */ /* 82C710 configuration register 0x02 */ #define UPC1_CR2_SCLK 0x40 /* Divide UART clock by 4 rather than 2 */ #define UPC1_CR2_RXSRC 0x20 /* Use divider output for Rx clock */ #define UPC1_CR2_TXSRC 0x10 /* Use divider output for Tx clock */ /* 82C710 configuration register 0x04 */ #define UPC1_UARTBASE_SHIFT 2 /* 82C710 configuration register 0x06 */ #define UPC1_PARBASE_SHIFT 2 /* 82C710 configuration register 0x09 */ #define UPC1_GPCSBASE_SHIFT 2 /* 82C710 configuration register 0x0a */ #define UPC1_CRA_GPCSMASK_MASK 0xe0 /* how many GPCSBASE bits matter */ #define UPC1_CRA_GPCSMASK_SHIFT 1 #define UPC1_CRA_GPCSA1 0x08 /* Extra bit at the bottom of GPCSBASE */ #define UPC1_CRA_IDEBEN 0x04 /* IDEENLO* buffer enable */ #define UPC1_CRA_GPCSEN 0x02 /* GPCS enable */ #define UPC1_CRA_GPCSBEN 0x01 /* GPCS buffer enable */ /* 82C710 configuration register 0x0b */ #define UPC1_CRB_MINTRP 0x80 /* Mouse interrupt polarity: 1->low */ #define UPC1_CRB_FINTRP 0x40 /* Floppy interrupt polarity */ #define UPC1_CRB_SINTRP 0x20 /* Serial interrupt polarity */ #define UPC1_CRB_PINTRP 0x10 /* Parallel interrupt polarity */ #define UPC1_CRB_SPDWN 0x08 /* Serial port power down */ #define UPC1_CRB_PPWDN 0x02 /* Parallel port power down */ #define UPC1_CRB_GPCSOUT 0x01 /* GPCS*/OUT1 pin function select */ /* 82C710 configuration register 0x0c */ #define UPC1_CRC_IDEEN 0x80 /* IDE enable */ #define UPC1_CRC_IDEATXT 0x40 /* IDE AT/XT select */ #define UPC1_CRC_FDCEN 0x20 /* FDC enable */ #define UPC1_CRC_FPWDN 0x10 /* FDC power down */ #define UPC1_CRC_RTCCSEN 0x08 /* RTCCS* enable */ #define UPC1_CRC_RTCBEN 0x04 /* RTCCS* buffer enable */ #define UPC1_CRC_MDDWN 0x01 /* Mouse port power down */ /* 82C710 configuration register 0x0d */ #define UPC1_MOUSEBASE_SHIFT 2 /* 82C710 configuration register 0x0e */ #define UPC1_CRE_STEN 0x40 /* Serial port test enabled */ #define UPC1_CRE_FTEN1 0x10 /* Floppy test bit 1 */ #define UPC1_CRE_FTEN2 0x80 /* Floppy test bit 2 */ #define UPC1_CRE_DSTEN 0x40 /* 82C710 configuration register 0x0f */ #define UPC1_CONFBASE_SHIFT 2 /* 82C711/721 Configuration magic sequences */ #define UPC2_PORT_CFGADDR 0x3f0 /* Configuration register address */ #define UPC2_PORT_CFGDATA 0x3f1 /* Configuration register value */ #define UPC2_CFGMAGIC_ENTER 0x55 /* Write twice to enter config mode. */ #define UPC2_CFGMAGIC_EXIT 0xaa /* Write once to exit config mode. */ /* Configuration registers */ #define UPC2_CFGADDR_CR0 0x00 /* Configuration Register 0 */ #define UPC2_CFGADDR_CR1 0x01 /* Configuration Register 1 */ #define UPC2_CFGADDR_CR2 0x02 /* Configuration Register 2 */ #define UPC2_CFGADDR_CR3 0x03 /* Configuration Register 3 */ #define UPC2_CFGADDR_CR4 0x04 /* Configuration Register 4 */ /* Configuration register 0 */ #define UPC2_CR0_VALID 0x80 /* Device has been configured */ #define UPC2_CR0_OSC_MASK 0x60 /* Oscillator control */ #define UPC2_CR0_OSC_ON 0x00 /* Oscillator always on */ #define UPC2_CR0_OSC_PWRGD 0x20 /* Oscillator on when PWRGD */ #define UPC2_CR0_OSC_OFF 0x60 /* Oscillator always off */ #define UPC2_CR0_FDC_ENABLE 0x10 /* FDC enabled */ #define UPC2_CR0_FDC_ON 0x08 /* FDC powered */ #define UPC2_CR0_IDE_AT 0x02 /* IDE controller is AT type */ #define UPC2_CR0_IDE_ENABLE 0x01 /* IDE controller enabled */ /* Configuration register 1 */ #define UPC2_CR1_READ_ENABLE 0x80 /* Enable reading of config regs */ #define UPC2_CR1_COM34_MASK 0x60 /* COM3/COM4 addresses */ #define UPC2_CR1_COM34_338_238 0x00 /* COM3 = 0x338; COM4 = 0x238 */ #define UPC2_CR1_COM34_3E8_2E8 0x20 /* COM3 = 0x3E8; COM4 = 0x2E8 */ #define UPC2_CR1_COM34_2E8_2E0 0x40 /* COM3 = 0x2E8; COM4 = 0x2E0 */ #define UPC2_CR1_COM34_220_228 0x60 /* COM3 = 0x220; COM4 = 0x228 */ #define UPC2_CR1_IRQ_ACTHIGH 0x10 /* IRQ is active-high */ #define UPC2_CR1_LPT_BORING 0x08 /* Parallel port is not EPP */ #define UPC2_CR1_LPT_ON 0x04 /* Parallel port is powered */ #define UPC2_CR1_LPT_MASK 0x03 /* Parallel port address */ #define UPC2_CR1_LPT_DISABLE 0x00 /* Parallel port disabled */ #define UPC2_CR1_LPT_3BC 0x01 /* Parallel port at 0x3BC */ #define UPC2_CR1_LPT_378 0x02 /* Parallel port at 0x378 */ #define UPC2_CR1_LPT_278 0x03 /* Parallel port at 0x278 */ /* Configuration register 2 */ #define UPC2_CR2_UART2_ON 0x80 /* 2ndary serial powered */ #define UPC2_CR2_UART2_ENABLE 0x40 /* 2ndary serial enabled */ #define UPC2_CR2_UART2_MASK 0x30 /* 2ndary serial address */ #define UPC2_CR2_UART2_3F8 0x00 /* 2ndary serial at 0x3F8 */ #define UPC2_CR2_UART2_2F8 0x10 /* 2ndary serial at 0x2F8 */ #define UPC2_CR2_UART2_COM3 0x20 /* 2ndary serial at COM3 (see CR1) */ #define UPC2_CR2_UART2_COM4 0x30 /* 2ndary serial at COM4 (see CR1) */ #define UPC2_CR2_UART1_ON 0x08 /* primary serial powered */ #define UPC2_CR2_UART1_ENABLE 0x04 /* primary serial enabled */ #define UPC2_CR2_UART1_MASK 0x03 /* primary serial address */ #define UPC2_CR2_UART1_3F8 0x00 /* primary serial at 0x3F8 */ #define UPC2_CR2_UART1_2F8 0x01 /* primary serial at 0x2F8 */ #define UPC2_CR2_UART1_COM3 0x02 /* primary serial at COM3 (see CR1) */ #define UPC2_CR2_UART1_COM4 0x03 /* primary serial at COM4 (see CR1) */ /* Configuration register 3 */ #define UPC2_CR3_UART2_TEST 0x80 /* 2ndary serial test mode */ #define UPC2_CR3_UART1_TEST 0x40 /* primary serial test mode */ #define UPC2_CR3_FDC_TEST_MASK 0x30 /* FDC test modes */ #define UPC2_CR3_FDC_TEST_NORMAL 0x00 /* FDC normal mode */ /* Configuration register 4 (82C721 only) */ #define UPC2_CR4_UART2_DIV13 0x01 /* Use normal (cf MIDI) clock for UART2 */