/*- * Copyright (c) 2002 The NetBSD Foundation, Inc. * All rights reserved. * * This code is derived from software contributed to The NetBSD Foundation * by Martin Husemann . * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * * THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED * TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE * POSSIBILITY OF SUCH DAMAGE. */ #include __KERNEL_RCSID(0, "$NetBSD: isic_isa_itk_ix1.c,v 1.18 2012/10/27 17:18:25 chs Exp $"); #include "opt_isicisa.h" /* * The ITK ix1 micro ISDN card is an ISA card with one region * of four io ports mapped and a fixed irq all jumpered on the card. * Access to the board is straight forward and simmilar to * the ELSA and DYNALINK cards. If a PCI version of this card * exists all we need is probably a pci-bus attachment, all * this low level routines should work immediately. * * To reset the card: * - write 0x01 to ITK_CONFIG * - wait >= 10 ms * - write 0x00 to ITK_CONFIG * * To read or write data: * - write address to ITK_ALE port * - read data from or write data to ITK_ISAC_DATA port or ITK_HSCX_DATA port * The two HSCX channel registers are offset by HSCXA (0x00) and HSCXB (0x40). * * The probe routine was derived by trial and error from a representative * sample of two cards ;-) The standard way (checking HSCX versions) * was extended by reading a zero from a non existent HSCX register (register * 0xff). Reading the config register gives varying results, so this doesn't * seem to be used as an id register (like the Teles S0/16.3). * * If the probe fails for your card use "options ITK_PROBE_DEBUG" to get * additional debug output. * */ #ifdef ISICISA_ITKIX1 #include #if defined(__FreeBSD__) && __FreeBSD__ >= 3 #include #else #include #endif #include #include #include #if defined(__NetBSD__) && __NetBSD_Version__ >= 104230000 #include #endif #ifdef __FreeBSD__ #include #include #else #include #include #endif #include #include #ifdef __FreeBSD__ #include #include #else #include #include #include #include #include #endif #include #include #include #include /* Register offsets */ #define ITK_ISAC_DATA 0 #define ITK_HSCX_DATA 1 #define ITK_ALE 2 #define ITK_CONFIG 3 /* Size of IO range to allocate for this card */ #define ITK_IO_SIZE 4 /* Register offsets for the two HSCX channels */ #define HSCXA 0 #define HSCXB 0x40 /* * Local function prototypes */ #ifdef __FreeBSD__ /* FreeBSD version */ static void itkix1_read_fifo(void *buf, const void *base, size_t len); static void itkix1_write_fifo(void *base, const void *buf, size_t len); static void itkix1_write_reg(u_char *base, u_int offset, u_int v); static u_char itkix1_read_reg(u_char *base, u_int offset); #else /* NetBSD/OpenBSD version */ static void itkix1_read_fifo(struct isic_softc *sc, int what, void *buf, size_t size); static void itkix1_write_fifo(struct isic_softc *sc, int what, const void *buf, size_t size); static void itkix1_write_reg(struct isic_softc *sc, int what, bus_size_t offs, u_int8_t data); static u_int8_t itkix1_read_reg(struct isic_softc *sc, int what, bus_size_t offs); #endif /* * Probe for card */ #ifdef __FreeBSD__ int isic_probe_itkix1(struct isa_device *dev) { u_int8_t hd, hv1, hv2, saveale; int ret; /* save old value of this port, we're stomping over it */ saveale = inb(dev->id_iobase + ITK_ALE); /* select invalid register */ outb(dev->id_iobase + ITK_ALE, 0xff); /* get HSCX data for this non existent register */ hd = inb(dev->id_iobase + ITK_HSCX_DATA); /* get HSCX version info */ outb(dev->id_iobase + ITK_ALE, HSCXA + H_VSTR); hv1 = inb(dev->id_iobase + ITK_HSCX_DATA); outb(dev->id_iobase + ITK_ALE, HSCXB + H_VSTR); hv2 = inb(dev->id_iobase + ITK_HSCX_DATA); /* succeed if version bits are OK and we got a zero from the * non existent register. we found verison 0x05 and 0x04 * out there... */ ret = (hd == 0) && (((hv1 & 0x0f) == 0x05) || ((hv1 & 0x0f) == 0x04)) && (((hv2 & 0x0f) == 0x05) || ((hv2 & 0x0f) == 0x04)); /* retstore save value if we fail (if we succeed the old value * has no meaning) */ if (!ret) outb(dev->id_iobase + ITK_ALE, saveale); #ifdef ITK_PROBE_DEBUG printf("\nITK ix1 micro probe: hscx = 0x%02x, v1 = 0x%02x, v2 = 0x%02x, would have %s\n", hd, hv1, hv2, ret ? "succeeded" : "failed"); return 1; #else return ret; #endif } #else int isic_probe_itkix1(struct isic_attach_args *ia) { bus_space_tag_t t = ia->ia_maps[0].t; bus_space_handle_t h = ia->ia_maps[0].h; u_int8_t hd, hv1, hv2, saveale; int ret; /* save old value of this port, we're stomping over it */ saveale = bus_space_read_1(t, h, ITK_ALE); /* select invalid register */ bus_space_write_1(t, h, ITK_ALE, 0xff); /* get HSCX data for this non existent register */ hd = bus_space_read_1(t, h, ITK_HSCX_DATA); /* get HSCX version info */ bus_space_write_1(t, h, ITK_ALE, HSCXA + H_VSTR); hv1 = bus_space_read_1(t, h, ITK_HSCX_DATA); bus_space_write_1(t, h, ITK_ALE, HSCXB + H_VSTR); hv2 = bus_space_read_1(t, h, ITK_HSCX_DATA); ret = (hd == 0) && ((hv1 & 0x0f) == 0x05) && ((hv2 & 0x0f) == 0x05); /* succeed if version bits are OK and we got a zero from the * non existent register. we found verison 0x05 and 0x04 * out there... */ ret = (hd == 0) && (((hv1 & 0x0f) == 0x05) || ((hv1 & 0x0f) == 0x04)) && (((hv2 & 0x0f) == 0x05) || ((hv2 & 0x0f) == 0x04)); /* retstore save value if we fail (if we succeed the old value * has no meaning) */ if (!ret) bus_space_write_1(t, h, ITK_ALE, saveale); #ifdef ITK_PROBE_DEBUG printf("\nITK ix1 micro probe: hscx = 0x%02x, v1 = 0x%02x, v2 = 0x%02x, would have %s\n", hd, hv1, hv2, ret ? "succeeded" : "failed"); return 1; #else return ret; #endif } #endif /* * Attach card */ #ifdef __FreeBSD__ int isic_attach_itkix1(struct isa_device *dev) { struct isic_softc *sc = &l1_sc[dev->id_unit]; u_int8_t hv1, hv2; sc->sc_irq = dev->id_irq; dev->id_msize = 0; /* check if we got an iobase */ sc->sc_port = dev->id_iobase; /* setup access routines */ sc->clearirq = NULL; sc->readreg = itkix1_read_reg; sc->writereg = itkix1_write_reg; sc->readfifo = itkix1_read_fifo; sc->writefifo = itkix1_write_fifo; /* setup card type */ sc->sc_cardtyp = CARD_TYPEP_ITKIX1; /* setup IOM bus type */ sc->sc_bustyp = BUS_TYPE_IOM2; sc->sc_ipac = 0; sc->sc_bfifolen = HSCX_FIFO_LEN; /* setup ISAC and HSCX base addr */ ISAC_BASE = (void *) sc->sc_port; HSCX_A_BASE = (void *) sc->sc_port + 1; HSCX_B_BASE = (void *) sc->sc_port + 2; /* Read HSCX A/B VSTR. Expected value is 0x05 (V2.1) or 0x04 (V2.0). */ hv1 = HSCX_READ(0, H_VSTR) & 0xf; hv2 = HSCX_READ(1, H_VSTR) & 0xf; if((hv1 != 0x05 && hv1 != 0x04) || (hv2 != 0x05 && hv2 != 0x04)) { printf("isic%d: HSCX VSTR test failed for ITK ix1 micro\n", dev->id_unit); printf("isic%d: HSC0: VSTR: %#x\n", dev->id_unit, HSCX_READ(0, H_VSTR)); printf("isic%d: HSC1: VSTR: %#x\n", dev->id_unit, HSCX_READ(1, H_VSTR)); return (0); } outb((dev->id_iobase)+ITK_CONFIG, 1); DELAY(SEC_DELAY / 10); outb((dev->id_iobase)+ITK_CONFIG, 0); DELAY(SEC_DELAY / 10); return(1); } #else int isic_attach_itkix1(struct isic_softc *sc) { u_int8_t hv1, hv2; /* setup access routines */ sc->clearirq = NULL; sc->readreg = itkix1_read_reg; sc->writereg = itkix1_write_reg; sc->readfifo = itkix1_read_fifo; sc->writefifo = itkix1_write_fifo; /* setup card type */ sc->sc_cardtyp = CARD_TYPEP_ITKIX1; /* setup IOM bus type */ sc->sc_bustyp = BUS_TYPE_IOM2; sc->sc_ipac = 0; sc->sc_bfifolen = HSCX_FIFO_LEN; /* Read HSCX A/B VSTR. Expected value is 0x05 (V2.1) or 0x04 (V2.0). */ hv1 = HSCX_READ(0, H_VSTR) & 0xf; hv2 = HSCX_READ(1, H_VSTR) & 0xf; if((hv1 != 0x05 && hv1 != 0x04) || (hv2 != 0x05 && hv2 != 0x04)) { printf("%s: HSCX VSTR test failed for ITK ix1 micro\n", device_xname(sc->sc_dev)); printf("%s: HSC0: VSTR: %#x\n", device_xname(sc->sc_dev), HSCX_READ(0, H_VSTR)); printf("%s: HSC1: VSTR: %#x\n", device_xname(sc->sc_dev), HSCX_READ(1, H_VSTR)); return 0; } bus_space_write_1(sc->sc_maps[0].t, sc->sc_maps[0].h, ITK_CONFIG, 1); DELAY(SEC_DELAY / 10); bus_space_write_1(sc->sc_maps[0].t, sc->sc_maps[0].h, ITK_CONFIG, 0); DELAY(SEC_DELAY / 10); return 1; } #endif #ifdef __FreeBSD__ static void itkix1_read_fifo(void *buf, const void *base, size_t len) { u_int port = (u_int)base & ~0x0003; switch ((u_int)base & 3) { case 0: /* ISAC */ outb(port+ITK_ALE, 0); insb(port+ITK_ISAC_DATA, (u_char *)buf, (u_int)len); break; case 1: /* HSCXA */ outb(port+ITK_ALE, HSCXA); insb(port+ITK_HSCX_DATA, (u_char *)buf, (u_int)len); break; case 2: /* HSCXB */ outb(port+ITK_ALE, HSCXB); insb(port+ITK_HSCX_DATA, (u_char *)buf, (u_int)len); break; } } #else static void itkix1_read_fifo(struct isic_softc *sc, int what, void *buf, size_t size) { bus_space_tag_t t = sc->sc_maps[0].t; bus_space_handle_t h = sc->sc_maps[0].h; switch (what) { case ISIC_WHAT_ISAC: bus_space_write_1(t, h, ITK_ALE, 0); bus_space_read_multi_1(t, h, ITK_ISAC_DATA, buf, size); break; case ISIC_WHAT_HSCXA: bus_space_write_1(t, h, ITK_ALE, HSCXA); bus_space_read_multi_1(t, h, ITK_HSCX_DATA, buf, size); break; case ISIC_WHAT_HSCXB: bus_space_write_1(t, h, ITK_ALE, HSCXB); bus_space_read_multi_1(t, h, ITK_HSCX_DATA, buf, size); break; } } #endif #ifdef __FreeBSD__ static void itkix1_write_fifo(void *base, const void *buf, size_t len) { u_int port = (u_int)base & ~0x0003; switch ((u_int)base & 3) { case 0: /* ISAC */ outb(port+ITK_ALE, 0); outsb(port+ITK_ISAC_DATA, (u_char *)buf, (u_int)len); break; case 1: /* HSCXA */ outb(port+ITK_ALE, HSCXA); outsb(port+ITK_HSCX_DATA, (u_char *)buf, (u_int)len); break; case 2: /* HSCXB */ outb(port+ITK_ALE, HSCXB); outsb(port+ITK_HSCX_DATA, (u_char *)buf, (u_int)len); break; } } #else static void itkix1_write_fifo(struct isic_softc *sc, int what, const void *buf, size_t size) { bus_space_tag_t t = sc->sc_maps[0].t; bus_space_handle_t h = sc->sc_maps[0].h; switch (what) { case ISIC_WHAT_ISAC: bus_space_write_1(t, h, ITK_ALE, 0); bus_space_write_multi_1(t, h, ITK_ISAC_DATA, buf, size); break; case ISIC_WHAT_HSCXA: bus_space_write_1(t, h, ITK_ALE, HSCXA); bus_space_write_multi_1(t, h, ITK_HSCX_DATA, buf, size); break; case ISIC_WHAT_HSCXB: bus_space_write_1(t, h, ITK_ALE, HSCXB); bus_space_write_multi_1(t, h, ITK_HSCX_DATA, buf, size); break; } } #endif #ifdef __FreeBSD__ static void itkix1_write_reg(u_char *base, u_int offset, u_int v) { u_int port = (u_int)base & ~0x0003; switch ((u_int)base & 3) { case 0: /* ISAC */ outb(port+ITK_ALE, offset); outb(port+ITK_ISAC_DATA, (u_char)v); break; case 1: /* HSCXA */ outb(port+ITK_ALE, HSCXA+offset); outb(port+ITK_HSCX_DATA, (u_char)v); break; case 2: /* HSCXB */ outb(port+ITK_ALE, HSCXB+offset); outb(port+ITK_HSCX_DATA, (u_char)v); break; } } #else static void itkix1_write_reg(struct isic_softc *sc, int what, bus_size_t offs, u_int8_t data) { bus_space_tag_t t = sc->sc_maps[0].t; bus_space_handle_t h = sc->sc_maps[0].h; switch (what) { case ISIC_WHAT_ISAC: bus_space_write_1(t, h, ITK_ALE, offs); bus_space_write_1(t, h, ITK_ISAC_DATA, data); break; case ISIC_WHAT_HSCXA: bus_space_write_1(t, h, ITK_ALE, HSCXA+offs); bus_space_write_1(t, h, ITK_HSCX_DATA, data); break; case ISIC_WHAT_HSCXB: bus_space_write_1(t, h, ITK_ALE, HSCXB+offs); bus_space_write_1(t, h, ITK_HSCX_DATA, data); break; } } #endif #ifdef __FreeBSD__ static u_char itkix1_read_reg(u_char *base, u_int offset) { u_int port = (u_int)base & ~0x0003; switch ((u_int)base & 3) { case 0: /* ISAC */ outb(port+ITK_ALE, offset); return (inb(port+ITK_ISAC_DATA)); case 1: /* HSCXA */ outb(port+ITK_ALE, HSCXA+offset); return (inb(port+ITK_HSCX_DATA)); case 2: /* HSCXB */ outb(port+ITK_ALE, HSCXB+offset); return (inb(port+ITK_HSCX_DATA)); } } #else static u_int8_t itkix1_read_reg(struct isic_softc *sc, int what, bus_size_t offs) { bus_space_tag_t t = sc->sc_maps[0].t; bus_space_handle_t h = sc->sc_maps[0].h; switch (what) { case ISIC_WHAT_ISAC: bus_space_write_1(t, h, ITK_ALE, offs); return bus_space_read_1(t, h, ITK_ISAC_DATA); case ISIC_WHAT_HSCXA: bus_space_write_1(t, h, ITK_ALE, HSCXA+offs); return bus_space_read_1(t, h, ITK_HSCX_DATA); case ISIC_WHAT_HSCXB: bus_space_write_1(t, h, ITK_ALE, HSCXB+offs); return bus_space_read_1(t, h, ITK_HSCX_DATA); } return 0; } #endif #endif /* ISICISA_ITKIX1 */