/* $NetBSD: if_stge.c,v 1.62.8.3 2019/11/14 16:04:31 martin Exp $ */ /*- * Copyright (c) 2001 The NetBSD Foundation, Inc. * All rights reserved. * * This code is derived from software contributed to The NetBSD Foundation * by Jason R. Thorpe. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * * THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED * TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE * POSSIBILITY OF SUCH DAMAGE. */ /* * Device driver for the Sundance Tech. TC9021 10/100/1000 * Ethernet controller. */ #include __KERNEL_RCSID(0, "$NetBSD: if_stge.c,v 1.62.8.3 2019/11/14 16:04:31 martin Exp $"); #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include /* #define STGE_CU_BUG 1 */ #define STGE_VLAN_UNTAG 1 /* #define STGE_VLAN_CFI 1 */ /* * Transmit descriptor list size. */ #define STGE_NTXDESC 256 #define STGE_NTXDESC_MASK (STGE_NTXDESC - 1) #define STGE_NEXTTX(x) (((x) + 1) & STGE_NTXDESC_MASK) /* * Receive descriptor list size. */ #define STGE_NRXDESC 256 #define STGE_NRXDESC_MASK (STGE_NRXDESC - 1) #define STGE_NEXTRX(x) (((x) + 1) & STGE_NRXDESC_MASK) /* * Only interrupt every N frames. Must be a power-of-two. */ #define STGE_TXINTR_SPACING 16 #define STGE_TXINTR_SPACING_MASK (STGE_TXINTR_SPACING - 1) /* * Control structures are DMA'd to the TC9021 chip. We allocate them in * a single clump that maps to a single DMA segment to make several things * easier. */ struct stge_control_data { /* * The transmit descriptors. */ struct stge_tfd scd_txdescs[STGE_NTXDESC]; /* * The receive descriptors. */ struct stge_rfd scd_rxdescs[STGE_NRXDESC]; }; #define STGE_CDOFF(x) offsetof(struct stge_control_data, x) #define STGE_CDTXOFF(x) STGE_CDOFF(scd_txdescs[(x)]) #define STGE_CDRXOFF(x) STGE_CDOFF(scd_rxdescs[(x)]) /* * Software state for transmit and receive jobs. */ struct stge_descsoft { struct mbuf *ds_mbuf; /* head of our mbuf chain */ bus_dmamap_t ds_dmamap; /* our DMA map */ }; /* * Software state per device. */ struct stge_softc { device_t sc_dev; /* generic device information */ bus_space_tag_t sc_st; /* bus space tag */ bus_space_handle_t sc_sh; /* bus space handle */ bus_dma_tag_t sc_dmat; /* bus DMA tag */ struct ethercom sc_ethercom; /* ethernet common data */ int sc_rev; /* silicon revision */ void *sc_ih; /* interrupt cookie */ struct mii_data sc_mii; /* MII/media information */ callout_t sc_tick_ch; /* tick callout */ bus_dmamap_t sc_cddmamap; /* control data DMA map */ #define sc_cddma sc_cddmamap->dm_segs[0].ds_addr /* * Software state for transmit and receive descriptors. */ struct stge_descsoft sc_txsoft[STGE_NTXDESC]; struct stge_descsoft sc_rxsoft[STGE_NRXDESC]; /* * Control data structures. */ struct stge_control_data *sc_control_data; #define sc_txdescs sc_control_data->scd_txdescs #define sc_rxdescs sc_control_data->scd_rxdescs #ifdef STGE_EVENT_COUNTERS /* * Event counters. */ struct evcnt sc_ev_txstall; /* Tx stalled */ struct evcnt sc_ev_txdmaintr; /* Tx DMA interrupts */ struct evcnt sc_ev_txindintr; /* Tx Indicate interrupts */ struct evcnt sc_ev_rxintr; /* Rx interrupts */ struct evcnt sc_ev_txseg1; /* Tx packets w/ 1 segment */ struct evcnt sc_ev_txseg2; /* Tx packets w/ 2 segments */ struct evcnt sc_ev_txseg3; /* Tx packets w/ 3 segments */ struct evcnt sc_ev_txseg4; /* Tx packets w/ 4 segments */ struct evcnt sc_ev_txseg5; /* Tx packets w/ 5 segments */ struct evcnt sc_ev_txsegmore; /* Tx packets w/ more than 5 segments */ struct evcnt sc_ev_txcopy; /* Tx packets that we had to copy */ struct evcnt sc_ev_rxipsum; /* IP checksums checked in-bound */ struct evcnt sc_ev_rxtcpsum; /* TCP checksums checked in-bound */ struct evcnt sc_ev_rxudpsum; /* UDP checksums checked in-bound */ struct evcnt sc_ev_txipsum; /* IP checksums comp. out-bound */ struct evcnt sc_ev_txtcpsum; /* TCP checksums comp. out-bound */ struct evcnt sc_ev_txudpsum; /* UDP checksums comp. out-bound */ #endif /* STGE_EVENT_COUNTERS */ int sc_txpending; /* number of Tx requests pending */ int sc_txdirty; /* first dirty Tx descriptor */ int sc_txlast; /* last used Tx descriptor */ int sc_rxptr; /* next ready Rx descriptor/descsoft */ int sc_rxdiscard; int sc_rxlen; struct mbuf *sc_rxhead; struct mbuf *sc_rxtail; struct mbuf **sc_rxtailp; int sc_txthresh; /* Tx threshold */ uint32_t sc_usefiber:1; /* if we're fiber */ uint32_t sc_stge1023:1; /* are we a 1023 */ uint32_t sc_DMACtrl; /* prototype DMACtrl register */ uint32_t sc_MACCtrl; /* prototype MacCtrl register */ uint16_t sc_IntEnable; /* prototype IntEnable register */ uint16_t sc_ReceiveMode; /* prototype ReceiveMode register */ uint8_t sc_PhyCtrl; /* prototype PhyCtrl register */ }; #define STGE_RXCHAIN_RESET(sc) \ do { \ (sc)->sc_rxtailp = &(sc)->sc_rxhead; \ *(sc)->sc_rxtailp = NULL; \ (sc)->sc_rxlen = 0; \ } while (/*CONSTCOND*/0) #define STGE_RXCHAIN_LINK(sc, m) \ do { \ *(sc)->sc_rxtailp = (sc)->sc_rxtail = (m); \ (sc)->sc_rxtailp = &(m)->m_next; \ } while (/*CONSTCOND*/0) #ifdef STGE_EVENT_COUNTERS #define STGE_EVCNT_INCR(ev) (ev)->ev_count++ #else #define STGE_EVCNT_INCR(ev) /* nothing */ #endif #define STGE_CDTXADDR(sc, x) ((sc)->sc_cddma + STGE_CDTXOFF((x))) #define STGE_CDRXADDR(sc, x) ((sc)->sc_cddma + STGE_CDRXOFF((x))) #define STGE_CDTXSYNC(sc, x, ops) \ bus_dmamap_sync((sc)->sc_dmat, (sc)->sc_cddmamap, \ STGE_CDTXOFF((x)), sizeof(struct stge_tfd), (ops)) #define STGE_CDRXSYNC(sc, x, ops) \ bus_dmamap_sync((sc)->sc_dmat, (sc)->sc_cddmamap, \ STGE_CDRXOFF((x)), sizeof(struct stge_rfd), (ops)) #define STGE_INIT_RXDESC(sc, x) \ do { \ struct stge_descsoft *__ds = &(sc)->sc_rxsoft[(x)]; \ struct stge_rfd *__rfd = &(sc)->sc_rxdescs[(x)]; \ \ /* \ * Note: We scoot the packet forward 2 bytes in the buffer \ * so that the payload after the Ethernet header is aligned \ * to a 4-byte boundary. \ */ \ __rfd->rfd_frag.frag_word0 = \ htole64(FRAG_ADDR(__ds->ds_dmamap->dm_segs[0].ds_addr + 2) |\ FRAG_LEN(MCLBYTES - 2)); \ __rfd->rfd_next = \ htole64((uint64_t)STGE_CDRXADDR((sc), STGE_NEXTRX((x)))); \ __rfd->rfd_status = 0; \ STGE_CDRXSYNC((sc), (x), BUS_DMASYNC_PREREAD|BUS_DMASYNC_PREWRITE); \ } while (/*CONSTCOND*/0) #define STGE_TIMEOUT 1000 static void stge_start(struct ifnet *); static void stge_watchdog(struct ifnet *); static int stge_ioctl(struct ifnet *, u_long, void *); static int stge_init(struct ifnet *); static void stge_stop(struct ifnet *, int); static bool stge_shutdown(device_t, int); static void stge_reset(struct stge_softc *); static void stge_rxdrain(struct stge_softc *); static int stge_add_rxbuf(struct stge_softc *, int); static void stge_read_eeprom(struct stge_softc *, int, uint16_t *); static void stge_tick(void *); static void stge_stats_update(struct stge_softc *); static void stge_set_filter(struct stge_softc *); static int stge_intr(void *); static void stge_txintr(struct stge_softc *); static void stge_rxintr(struct stge_softc *); static int stge_mii_readreg(device_t, int, int); static void stge_mii_writereg(device_t, int, int, int); static void stge_mii_statchg(struct ifnet *); static int stge_match(device_t, cfdata_t, void *); static void stge_attach(device_t, device_t, void *); int stge_copy_small = 0; CFATTACH_DECL_NEW(stge, sizeof(struct stge_softc), stge_match, stge_attach, NULL, NULL); static uint32_t stge_mii_bitbang_read(device_t); static void stge_mii_bitbang_write(device_t, uint32_t); static const struct mii_bitbang_ops stge_mii_bitbang_ops = { stge_mii_bitbang_read, stge_mii_bitbang_write, { PC_MgmtData, /* MII_BIT_MDO */ PC_MgmtData, /* MII_BIT_MDI */ PC_MgmtClk, /* MII_BIT_MDC */ PC_MgmtDir, /* MII_BIT_DIR_HOST_PHY */ 0, /* MII_BIT_DIR_PHY_HOST */ } }; /* * Devices supported by this driver. */ static const struct stge_product { pci_vendor_id_t stge_vendor; pci_product_id_t stge_product; const char *stge_name; } stge_products[] = { { PCI_VENDOR_SUNDANCETI, PCI_PRODUCT_SUNDANCETI_ST1023, "Sundance ST-1023 Gigabit Ethernet" }, { PCI_VENDOR_SUNDANCETI, PCI_PRODUCT_SUNDANCETI_ST2021, "Sundance ST-2021 Gigabit Ethernet" }, { PCI_VENDOR_TAMARACK, PCI_PRODUCT_TAMARACK_TC9021, "Tamarack TC9021 Gigabit Ethernet" }, { PCI_VENDOR_TAMARACK, PCI_PRODUCT_TAMARACK_TC9021_ALT, "Tamarack TC9021 Gigabit Ethernet" }, /* * The Sundance sample boards use the Sundance vendor ID, * but the Tamarack product ID. */ { PCI_VENDOR_SUNDANCETI, PCI_PRODUCT_TAMARACK_TC9021, "Sundance TC9021 Gigabit Ethernet" }, { PCI_VENDOR_SUNDANCETI, PCI_PRODUCT_TAMARACK_TC9021_ALT, "Sundance TC9021 Gigabit Ethernet" }, { PCI_VENDOR_DLINK, PCI_PRODUCT_DLINK_DL4000, "D-Link DL-4000 Gigabit Ethernet" }, { PCI_VENDOR_ANTARES, PCI_PRODUCT_ANTARES_TC9021, "Antares Gigabit Ethernet" }, { 0, 0, NULL }, }; static const struct stge_product * stge_lookup(const struct pci_attach_args *pa) { const struct stge_product *sp; for (sp = stge_products; sp->stge_name != NULL; sp++) { if (PCI_VENDOR(pa->pa_id) == sp->stge_vendor && PCI_PRODUCT(pa->pa_id) == sp->stge_product) return (sp); } return (NULL); } static int stge_match(device_t parent, cfdata_t cf, void *aux) { struct pci_attach_args *pa = aux; if (stge_lookup(pa) != NULL) return (1); return (0); } static void stge_attach(device_t parent, device_t self, void *aux) { struct stge_softc *sc = device_private(self); struct pci_attach_args *pa = aux; struct ifnet *ifp = &sc->sc_ethercom.ec_if; pci_chipset_tag_t pc = pa->pa_pc; pci_intr_handle_t ih; const char *intrstr = NULL; bus_space_tag_t iot, memt; bus_space_handle_t ioh, memh; bus_dma_segment_t seg; prop_data_t data; int ioh_valid, memh_valid; int i, rseg, error; const struct stge_product *sp; uint8_t enaddr[ETHER_ADDR_LEN]; char intrbuf[PCI_INTRSTR_LEN]; sc->sc_dev = self; callout_init(&sc->sc_tick_ch, 0); sp = stge_lookup(pa); if (sp == NULL) { printf("\n"); panic("ste_attach: impossible"); } sc->sc_rev = PCI_REVISION(pa->pa_class); pci_aprint_devinfo_fancy(pa, NULL, sp->stge_name, 1); /* * Map the device. */ ioh_valid = (pci_mapreg_map(pa, STGE_PCI_IOBA, PCI_MAPREG_TYPE_IO, 0, &iot, &ioh, NULL, NULL) == 0); memh_valid = (pci_mapreg_map(pa, STGE_PCI_MMBA, PCI_MAPREG_TYPE_MEM|PCI_MAPREG_MEM_TYPE_32BIT, 0, &memt, &memh, NULL, NULL) == 0); if (memh_valid) { sc->sc_st = memt; sc->sc_sh = memh; } else if (ioh_valid) { sc->sc_st = iot; sc->sc_sh = ioh; } else { aprint_error_dev(self, "unable to map device registers\n"); return; } sc->sc_dmat = pa->pa_dmat; /* Enable bus mastering. */ pci_conf_write(pc, pa->pa_tag, PCI_COMMAND_STATUS_REG, pci_conf_read(pc, pa->pa_tag, PCI_COMMAND_STATUS_REG) | PCI_COMMAND_MASTER_ENABLE); /* power up chip */ if ((error = pci_activate(pa->pa_pc, pa->pa_tag, self, NULL)) && error != EOPNOTSUPP) { aprint_error_dev(self, "cannot activate %d\n", error); return; } /* * Map and establish our interrupt. */ if (pci_intr_map(pa, &ih)) { aprint_error_dev(self, "unable to map interrupt\n"); return; } intrstr = pci_intr_string(pc, ih, intrbuf, sizeof(intrbuf)); sc->sc_ih = pci_intr_establish(pc, ih, IPL_NET, stge_intr, sc); if (sc->sc_ih == NULL) { aprint_error_dev(self, "unable to establish interrupt"); if (intrstr != NULL) aprint_error(" at %s", intrstr); aprint_error("\n"); return; } aprint_normal_dev(self, "interrupting at %s\n", intrstr); /* * Allocate the control data structures, and create and load the * DMA map for it. */ if ((error = bus_dmamem_alloc(sc->sc_dmat, sizeof(struct stge_control_data), PAGE_SIZE, 0, &seg, 1, &rseg, 0)) != 0) { aprint_error_dev(self, "unable to allocate control data, error = %d\n", error); goto fail_0; } if ((error = bus_dmamem_map(sc->sc_dmat, &seg, rseg, sizeof(struct stge_control_data), (void **)&sc->sc_control_data, BUS_DMA_COHERENT)) != 0) { aprint_error_dev(self, "unable to map control data, error = %d\n", error); goto fail_1; } if ((error = bus_dmamap_create(sc->sc_dmat, sizeof(struct stge_control_data), 1, sizeof(struct stge_control_data), 0, 0, &sc->sc_cddmamap)) != 0) { aprint_error_dev(self, "unable to create control data DMA map, error = %d\n", error); goto fail_2; } if ((error = bus_dmamap_load(sc->sc_dmat, sc->sc_cddmamap, sc->sc_control_data, sizeof(struct stge_control_data), NULL, 0)) != 0) { aprint_error_dev(self, "unable to load control data DMA map, error = %d\n", error); goto fail_3; } /* * Create the transmit buffer DMA maps. Note that rev B.3 * and earlier seem to have a bug regarding multi-fragment * packets. We need to limit the number of Tx segments on * such chips to 1. */ for (i = 0; i < STGE_NTXDESC; i++) { if ((error = bus_dmamap_create(sc->sc_dmat, ETHER_MAX_LEN_JUMBO, STGE_NTXFRAGS, MCLBYTES, 0, 0, &sc->sc_txsoft[i].ds_dmamap)) != 0) { aprint_error_dev(self, "unable to create tx DMA map %d, error = %d\n", i, error); goto fail_4; } } /* * Create the receive buffer DMA maps. */ for (i = 0; i < STGE_NRXDESC; i++) { if ((error = bus_dmamap_create(sc->sc_dmat, MCLBYTES, 1, MCLBYTES, 0, 0, &sc->sc_rxsoft[i].ds_dmamap)) != 0) { aprint_error_dev(self, "unable to create rx DMA map %d, error = %d\n", i, error); goto fail_5; } sc->sc_rxsoft[i].ds_mbuf = NULL; } /* * Determine if we're copper or fiber. It affects how we * reset the card. */ if (bus_space_read_4(sc->sc_st, sc->sc_sh, STGE_AsicCtrl) & AC_PhyMedia) sc->sc_usefiber = 1; else sc->sc_usefiber = 0; /* * Reset the chip to a known state. */ stge_reset(sc); /* * Reading the station address from the EEPROM doesn't seem * to work, at least on my sample boards. Instead, since * the reset sequence does AutoInit, read it from the station * address registers. For Sundance 1023 you can only read it * from EEPROM. */ if (sp->stge_product != PCI_PRODUCT_SUNDANCETI_ST1023) { enaddr[0] = bus_space_read_2(sc->sc_st, sc->sc_sh, STGE_StationAddress0) & 0xff; enaddr[1] = bus_space_read_2(sc->sc_st, sc->sc_sh, STGE_StationAddress0) >> 8; enaddr[2] = bus_space_read_2(sc->sc_st, sc->sc_sh, STGE_StationAddress1) & 0xff; enaddr[3] = bus_space_read_2(sc->sc_st, sc->sc_sh, STGE_StationAddress1) >> 8; enaddr[4] = bus_space_read_2(sc->sc_st, sc->sc_sh, STGE_StationAddress2) & 0xff; enaddr[5] = bus_space_read_2(sc->sc_st, sc->sc_sh, STGE_StationAddress2) >> 8; sc->sc_stge1023 = 0; } else { data = prop_dictionary_get(device_properties(self), "mac-address"); if (data != NULL) { /* * Try to get the station address from device * properties first, in case the EEPROM is missing. */ KASSERT(prop_object_type(data) == PROP_TYPE_DATA); KASSERT(prop_data_size(data) == ETHER_ADDR_LEN); (void)memcpy(enaddr, prop_data_data_nocopy(data), ETHER_ADDR_LEN); } else { uint16_t myaddr[ETHER_ADDR_LEN / 2]; for (i = 0; i sc_stge1023 = 1; } aprint_normal_dev(self, "Ethernet address %s\n", ether_sprintf(enaddr)); /* * Read some important bits from the PhyCtrl register. */ sc->sc_PhyCtrl = bus_space_read_1(sc->sc_st, sc->sc_sh, STGE_PhyCtrl) & (PC_PhyDuplexPolarity | PC_PhyLnkPolarity); /* * Initialize our media structures and probe the MII. */ sc->sc_mii.mii_ifp = ifp; sc->sc_mii.mii_readreg = stge_mii_readreg; sc->sc_mii.mii_writereg = stge_mii_writereg; sc->sc_mii.mii_statchg = stge_mii_statchg; sc->sc_ethercom.ec_mii = &sc->sc_mii; ifmedia_init(&sc->sc_mii.mii_media, IFM_IMASK, ether_mediachange, ether_mediastatus); mii_attach(self, &sc->sc_mii, 0xffffffff, MII_PHY_ANY, MII_OFFSET_ANY, MIIF_DOPAUSE); if (LIST_FIRST(&sc->sc_mii.mii_phys) == NULL) { ifmedia_add(&sc->sc_mii.mii_media, IFM_ETHER|IFM_NONE, 0, NULL); ifmedia_set(&sc->sc_mii.mii_media, IFM_ETHER|IFM_NONE); } else ifmedia_set(&sc->sc_mii.mii_media, IFM_ETHER|IFM_AUTO); ifp = &sc->sc_ethercom.ec_if; strlcpy(ifp->if_xname, device_xname(self), IFNAMSIZ); ifp->if_softc = sc; ifp->if_flags = IFF_BROADCAST | IFF_SIMPLEX | IFF_MULTICAST; ifp->if_ioctl = stge_ioctl; ifp->if_start = stge_start; ifp->if_watchdog = stge_watchdog; ifp->if_init = stge_init; ifp->if_stop = stge_stop; IFQ_SET_READY(&ifp->if_snd); /* * The manual recommends disabling early transmit, so we * do. It's disabled anyway, if using IP checksumming, * since the entire packet must be in the FIFO in order * for the chip to perform the checksum. */ sc->sc_txthresh = 0x0fff; /* * Disable MWI if the PCI layer tells us to. */ sc->sc_DMACtrl = 0; if ((pa->pa_flags & PCI_FLAGS_MWI_OKAY) == 0) sc->sc_DMACtrl |= DMAC_MWIDisable; /* * We can support 802.1Q VLAN-sized frames and jumbo * Ethernet frames. * * XXX Figure out how to do hw-assisted VLAN tagging in * XXX a reasonable way on this chip. */ sc->sc_ethercom.ec_capabilities |= ETHERCAP_VLAN_MTU | /* XXX ETHERCAP_JUMBO_MTU | */ ETHERCAP_VLAN_HWTAGGING; /* * We can do IPv4/TCPv4/UDPv4 checksums in hardware. */ sc->sc_ethercom.ec_if.if_capabilities |= IFCAP_CSUM_IPv4_Tx | IFCAP_CSUM_IPv4_Rx | IFCAP_CSUM_TCPv4_Tx | IFCAP_CSUM_TCPv4_Rx | IFCAP_CSUM_UDPv4_Tx | IFCAP_CSUM_UDPv4_Rx; /* * Attach the interface. */ if_attach(ifp); if_deferred_start_init(ifp, NULL); ether_ifattach(ifp, enaddr); #ifdef STGE_EVENT_COUNTERS /* * Attach event counters. */ evcnt_attach_dynamic(&sc->sc_ev_txstall, EVCNT_TYPE_MISC, NULL, device_xname(self), "txstall"); evcnt_attach_dynamic(&sc->sc_ev_txdmaintr, EVCNT_TYPE_INTR, NULL, device_xname(self), "txdmaintr"); evcnt_attach_dynamic(&sc->sc_ev_txindintr, EVCNT_TYPE_INTR, NULL, device_xname(self), "txindintr"); evcnt_attach_dynamic(&sc->sc_ev_rxintr, EVCNT_TYPE_INTR, NULL, device_xname(self), "rxintr"); evcnt_attach_dynamic(&sc->sc_ev_txseg1, EVCNT_TYPE_MISC, NULL, device_xname(self), "txseg1"); evcnt_attach_dynamic(&sc->sc_ev_txseg2, EVCNT_TYPE_MISC, NULL, device_xname(self), "txseg2"); evcnt_attach_dynamic(&sc->sc_ev_txseg3, EVCNT_TYPE_MISC, NULL, device_xname(self), "txseg3"); evcnt_attach_dynamic(&sc->sc_ev_txseg4, EVCNT_TYPE_MISC, NULL, device_xname(self), "txseg4"); evcnt_attach_dynamic(&sc->sc_ev_txseg5, EVCNT_TYPE_MISC, NULL, device_xname(self), "txseg5"); evcnt_attach_dynamic(&sc->sc_ev_txsegmore, EVCNT_TYPE_MISC, NULL, device_xname(self), "txsegmore"); evcnt_attach_dynamic(&sc->sc_ev_txcopy, EVCNT_TYPE_MISC, NULL, device_xname(self), "txcopy"); evcnt_attach_dynamic(&sc->sc_ev_rxipsum, EVCNT_TYPE_MISC, NULL, device_xname(self), "rxipsum"); evcnt_attach_dynamic(&sc->sc_ev_rxtcpsum, EVCNT_TYPE_MISC, NULL, device_xname(self), "rxtcpsum"); evcnt_attach_dynamic(&sc->sc_ev_rxudpsum, EVCNT_TYPE_MISC, NULL, device_xname(self), "rxudpsum"); evcnt_attach_dynamic(&sc->sc_ev_txipsum, EVCNT_TYPE_MISC, NULL, device_xname(self), "txipsum"); evcnt_attach_dynamic(&sc->sc_ev_txtcpsum, EVCNT_TYPE_MISC, NULL, device_xname(self), "txtcpsum"); evcnt_attach_dynamic(&sc->sc_ev_txudpsum, EVCNT_TYPE_MISC, NULL, device_xname(self), "txudpsum"); #endif /* STGE_EVENT_COUNTERS */ /* * Make sure the interface is shutdown during reboot. */ if (pmf_device_register1(self, NULL, NULL, stge_shutdown)) pmf_class_network_register(self, ifp); else aprint_error_dev(self, "couldn't establish power handler\n"); return; /* * Free any resources we've allocated during the failed attach * attempt. Do this in reverse order and fall through. */ fail_5: for (i = 0; i < STGE_NRXDESC; i++) { if (sc->sc_rxsoft[i].ds_dmamap != NULL) bus_dmamap_destroy(sc->sc_dmat, sc->sc_rxsoft[i].ds_dmamap); } fail_4: for (i = 0; i < STGE_NTXDESC; i++) { if (sc->sc_txsoft[i].ds_dmamap != NULL) bus_dmamap_destroy(sc->sc_dmat, sc->sc_txsoft[i].ds_dmamap); } bus_dmamap_unload(sc->sc_dmat, sc->sc_cddmamap); fail_3: bus_dmamap_destroy(sc->sc_dmat, sc->sc_cddmamap); fail_2: bus_dmamem_unmap(sc->sc_dmat, (void *)sc->sc_control_data, sizeof(struct stge_control_data)); fail_1: bus_dmamem_free(sc->sc_dmat, &seg, rseg); fail_0: return; } /* * stge_shutdown: * * Make sure the interface is stopped at reboot time. */ static bool stge_shutdown(device_t self, int howto) { struct stge_softc *sc = device_private(self); struct ifnet *ifp = &sc->sc_ethercom.ec_if; stge_stop(ifp, 1); stge_reset(sc); return true; } static void stge_dma_wait(struct stge_softc *sc) { int i; for (i = 0; i < STGE_TIMEOUT; i++) { delay(2); if ((bus_space_read_4(sc->sc_st, sc->sc_sh, STGE_DMACtrl) & DMAC_TxDMAInProg) == 0) break; } if (i == STGE_TIMEOUT) printf("%s: DMA wait timed out\n", device_xname(sc->sc_dev)); } /* * stge_start: [ifnet interface function] * * Start packet transmission on the interface. */ static void stge_start(struct ifnet *ifp) { struct stge_softc *sc = ifp->if_softc; struct mbuf *m0; struct stge_descsoft *ds; struct stge_tfd *tfd; bus_dmamap_t dmamap; int error, firsttx, nexttx, opending, seg, totlen; uint64_t csum_flags; if ((ifp->if_flags & (IFF_RUNNING|IFF_OACTIVE)) != IFF_RUNNING) return; /* * Remember the previous number of pending transmissions * and the first descriptor we will use. */ opending = sc->sc_txpending; firsttx = STGE_NEXTTX(sc->sc_txlast); /* * Loop through the send queue, setting up transmit descriptors * until we drain the queue, or use up all available transmit * descriptors. */ for (;;) { uint64_t tfc; bool have_vtag; uint16_t vtag; /* * Grab a packet off the queue. */ IFQ_POLL(&ifp->if_snd, m0); if (m0 == NULL) break; /* * Leave one unused descriptor at the end of the * list to prevent wrapping completely around. */ if (sc->sc_txpending == (STGE_NTXDESC - 1)) { STGE_EVCNT_INCR(&sc->sc_ev_txstall); break; } /* * See if we have any VLAN stuff. */ have_vtag = vlan_has_tag(m0); if (have_vtag) vtag = vlan_get_tag(m0); /* * Get the last and next available transmit descriptor. */ nexttx = STGE_NEXTTX(sc->sc_txlast); tfd = &sc->sc_txdescs[nexttx]; ds = &sc->sc_txsoft[nexttx]; dmamap = ds->ds_dmamap; /* * Load the DMA map. If this fails, the packet either * didn't fit in the alloted number of segments, or we * were short on resources. For the too-many-segments * case, we simply report an error and drop the packet, * since we can't sanely copy a jumbo packet to a single * buffer. */ error = bus_dmamap_load_mbuf(sc->sc_dmat, dmamap, m0, BUS_DMA_NOWAIT); if (error) { if (error == EFBIG) { printf("%s: Tx packet consumes too many " "DMA segments, dropping...\n", device_xname(sc->sc_dev)); IFQ_DEQUEUE(&ifp->if_snd, m0); m_freem(m0); continue; } /* * Short on resources, just stop for now. */ break; } IFQ_DEQUEUE(&ifp->if_snd, m0); /* * WE ARE NOW COMMITTED TO TRANSMITTING THE PACKET. */ /* Sync the DMA map. */ bus_dmamap_sync(sc->sc_dmat, dmamap, 0, dmamap->dm_mapsize, BUS_DMASYNC_PREWRITE); /* Initialize the fragment list. */ for (totlen = 0, seg = 0; seg < dmamap->dm_nsegs; seg++) { tfd->tfd_frags[seg].frag_word0 = htole64(FRAG_ADDR(dmamap->dm_segs[seg].ds_addr) | FRAG_LEN(dmamap->dm_segs[seg].ds_len)); totlen += dmamap->dm_segs[seg].ds_len; } #ifdef STGE_EVENT_COUNTERS switch (dmamap->dm_nsegs) { case 1: STGE_EVCNT_INCR(&sc->sc_ev_txseg1); break; case 2: STGE_EVCNT_INCR(&sc->sc_ev_txseg2); break; case 3: STGE_EVCNT_INCR(&sc->sc_ev_txseg3); break; case 4: STGE_EVCNT_INCR(&sc->sc_ev_txseg4); break; case 5: STGE_EVCNT_INCR(&sc->sc_ev_txseg5); break; default: STGE_EVCNT_INCR(&sc->sc_ev_txsegmore); break; } #endif /* STGE_EVENT_COUNTERS */ /* * Initialize checksumming flags in the descriptor. * Byte-swap constants so the compiler can optimize. */ csum_flags = 0; if (m0->m_pkthdr.csum_flags & M_CSUM_IPv4) { STGE_EVCNT_INCR(&sc->sc_ev_txipsum); csum_flags |= TFD_IPChecksumEnable; } if (m0->m_pkthdr.csum_flags & M_CSUM_TCPv4) { STGE_EVCNT_INCR(&sc->sc_ev_txtcpsum); csum_flags |= TFD_TCPChecksumEnable; } else if (m0->m_pkthdr.csum_flags & M_CSUM_UDPv4) { STGE_EVCNT_INCR(&sc->sc_ev_txudpsum); csum_flags |= TFD_UDPChecksumEnable; } /* * Initialize the descriptor and give it to the chip. * Check to see if we have a VLAN tag to insert. */ tfc = TFD_FrameId(nexttx) | TFD_WordAlign(/*totlen & */3) | TFD_FragCount(seg) | csum_flags | (((nexttx & STGE_TXINTR_SPACING_MASK) == 0) ? TFD_TxDMAIndicate : 0); if (have_vtag) { #if 0 struct ether_header *eh = mtod(m0, struct ether_header *); u_int16_t etype = ntohs(eh->ether_type); printf("%s: xmit (tag %d) etype %x\n", ifp->if_xname, *mtod(n, int *), etype); #endif tfc |= TFD_VLANTagInsert | #ifdef STGE_VLAN_CFI TFD_CFI | #endif TFD_VID(vtag); } tfd->tfd_control = htole64(tfc); /* Sync the descriptor. */ STGE_CDTXSYNC(sc, nexttx, BUS_DMASYNC_PREREAD|BUS_DMASYNC_PREWRITE); /* * Kick the transmit DMA logic. */ bus_space_write_4(sc->sc_st, sc->sc_sh, STGE_DMACtrl, sc->sc_DMACtrl | DMAC_TxDMAPollNow); /* * Store a pointer to the packet so we can free it later. */ ds->ds_mbuf = m0; /* Advance the tx pointer. */ sc->sc_txpending++; sc->sc_txlast = nexttx; /* * Pass the packet to any BPF listeners. */ bpf_mtap(ifp, m0); } if (sc->sc_txpending == (STGE_NTXDESC - 1)) { /* No more slots left; notify upper layer. */ ifp->if_flags |= IFF_OACTIVE; } if (sc->sc_txpending != opending) { /* * We enqueued packets. If the transmitter was idle, * reset the txdirty pointer. */ if (opending == 0) sc->sc_txdirty = firsttx; /* Set a watchdog timer in case the chip flakes out. */ ifp->if_timer = 5; } } /* * stge_watchdog: [ifnet interface function] * * Watchdog timer handler. */ static void stge_watchdog(struct ifnet *ifp) { struct stge_softc *sc = ifp->if_softc; /* * Sweep up first, since we don't interrupt every frame. */ stge_txintr(sc); if (sc->sc_txpending != 0) { printf("%s: device timeout\n", device_xname(sc->sc_dev)); ifp->if_oerrors++; (void) stge_init(ifp); /* Try to get more packets going. */ stge_start(ifp); } } /* * stge_ioctl: [ifnet interface function] * * Handle control requests from the operator. */ static int stge_ioctl(struct ifnet *ifp, u_long cmd, void *data) { struct stge_softc *sc = ifp->if_softc; int s, error; s = splnet(); error = ether_ioctl(ifp, cmd, data); if (error == ENETRESET) { error = 0; if (cmd != SIOCADDMULTI && cmd != SIOCDELMULTI) ; else if (ifp->if_flags & IFF_RUNNING) { /* * Multicast list has changed; set the hardware filter * accordingly. */ stge_set_filter(sc); } } /* Try to get more packets going. */ stge_start(ifp); splx(s); return (error); } /* * stge_intr: * * Interrupt service routine. */ static int stge_intr(void *arg) { struct stge_softc *sc = arg; struct ifnet *ifp = &sc->sc_ethercom.ec_if; uint32_t txstat; int wantinit; uint16_t isr; if ((bus_space_read_2(sc->sc_st, sc->sc_sh, STGE_IntStatus) & IS_InterruptStatus) == 0) return (0); for (wantinit = 0; wantinit == 0;) { isr = bus_space_read_2(sc->sc_st, sc->sc_sh, STGE_IntStatusAck); if ((isr & sc->sc_IntEnable) == 0) break; /* Host interface errors. */ if (isr & IS_HostError) { printf("%s: Host interface error\n", device_xname(sc->sc_dev)); wantinit = 1; continue; } /* Receive interrupts. */ if (isr & (IS_RxDMAComplete|IS_RFDListEnd)) { STGE_EVCNT_INCR(&sc->sc_ev_rxintr); stge_rxintr(sc); if (isr & IS_RFDListEnd) { printf("%s: receive ring overflow\n", device_xname(sc->sc_dev)); /* * XXX Should try to recover from this * XXX more gracefully. */ wantinit = 1; } } /* Transmit interrupts. */ if (isr & (IS_TxDMAComplete|IS_TxComplete)) { #ifdef STGE_EVENT_COUNTERS if (isr & IS_TxDMAComplete) STGE_EVCNT_INCR(&sc->sc_ev_txdmaintr); #endif stge_txintr(sc); } /* Statistics overflow. */ if (isr & IS_UpdateStats) stge_stats_update(sc); /* Transmission errors. */ if (isr & IS_TxComplete) { STGE_EVCNT_INCR(&sc->sc_ev_txindintr); for (;;) { txstat = bus_space_read_4(sc->sc_st, sc->sc_sh, STGE_TxStatus); if ((txstat & TS_TxComplete) == 0) break; if (txstat & TS_TxUnderrun) { sc->sc_txthresh++; if (sc->sc_txthresh > 0x0fff) sc->sc_txthresh = 0x0fff; printf("%s: transmit underrun, new " "threshold: %d bytes\n", device_xname(sc->sc_dev), sc->sc_txthresh << 5); } if (txstat & TS_MaxCollisions) printf("%s: excessive collisions\n", device_xname(sc->sc_dev)); } wantinit = 1; } } if (wantinit) stge_init(ifp); bus_space_write_2(sc->sc_st, sc->sc_sh, STGE_IntEnable, sc->sc_IntEnable); /* Try to get more packets going. */ if_schedule_deferred_start(ifp); return (1); } /* * stge_txintr: * * Helper; handle transmit interrupts. */ static void stge_txintr(struct stge_softc *sc) { struct ifnet *ifp = &sc->sc_ethercom.ec_if; struct stge_descsoft *ds; uint64_t control; int i; ifp->if_flags &= ~IFF_OACTIVE; /* * Go through our Tx list and free mbufs for those * frames which have been transmitted. */ for (i = sc->sc_txdirty; sc->sc_txpending != 0; i = STGE_NEXTTX(i), sc->sc_txpending--) { ds = &sc->sc_txsoft[i]; STGE_CDTXSYNC(sc, i, BUS_DMASYNC_POSTREAD|BUS_DMASYNC_POSTWRITE); control = le64toh(sc->sc_txdescs[i].tfd_control); if ((control & TFD_TFDDone) == 0) break; bus_dmamap_sync(sc->sc_dmat, ds->ds_dmamap, 0, ds->ds_dmamap->dm_mapsize, BUS_DMASYNC_POSTWRITE); bus_dmamap_unload(sc->sc_dmat, ds->ds_dmamap); m_freem(ds->ds_mbuf); ds->ds_mbuf = NULL; } /* Update the dirty transmit buffer pointer. */ sc->sc_txdirty = i; /* * If there are no more pending transmissions, cancel the watchdog * timer. */ if (sc->sc_txpending == 0) ifp->if_timer = 0; } /* * stge_rxintr: * * Helper; handle receive interrupts. */ static void stge_rxintr(struct stge_softc *sc) { struct ifnet *ifp = &sc->sc_ethercom.ec_if; struct stge_descsoft *ds; struct mbuf *m, *tailm; uint64_t status; int i, len; for (i = sc->sc_rxptr;; i = STGE_NEXTRX(i)) { ds = &sc->sc_rxsoft[i]; STGE_CDRXSYNC(sc, i, BUS_DMASYNC_POSTREAD|BUS_DMASYNC_POSTWRITE); status = le64toh(sc->sc_rxdescs[i].rfd_status); if ((status & RFD_RFDDone) == 0) break; if (__predict_false(sc->sc_rxdiscard)) { STGE_INIT_RXDESC(sc, i); if (status & RFD_FrameEnd) { /* Reset our state. */ sc->sc_rxdiscard = 0; } continue; } bus_dmamap_sync(sc->sc_dmat, ds->ds_dmamap, 0, ds->ds_dmamap->dm_mapsize, BUS_DMASYNC_POSTREAD); m = ds->ds_mbuf; /* * Add a new receive buffer to the ring. */ if (stge_add_rxbuf(sc, i) != 0) { /* * Failed, throw away what we've done so * far, and discard the rest of the packet. */ ifp->if_ierrors++; bus_dmamap_sync(sc->sc_dmat, ds->ds_dmamap, 0, ds->ds_dmamap->dm_mapsize, BUS_DMASYNC_POSTREAD); STGE_INIT_RXDESC(sc, i); if ((status & RFD_FrameEnd) == 0) sc->sc_rxdiscard = 1; if (sc->sc_rxhead != NULL) m_freem(sc->sc_rxhead); STGE_RXCHAIN_RESET(sc); continue; } #ifdef DIAGNOSTIC if (status & RFD_FrameStart) { KASSERT(sc->sc_rxhead == NULL); KASSERT(sc->sc_rxtailp == &sc->sc_rxhead); } #endif STGE_RXCHAIN_LINK(sc, m); /* * If this is not the end of the packet, keep * looking. */ if ((status & RFD_FrameEnd) == 0) { sc->sc_rxlen += m->m_len; continue; } /* * Okay, we have the entire packet now... */ *sc->sc_rxtailp = NULL; m = sc->sc_rxhead; tailm = sc->sc_rxtail; STGE_RXCHAIN_RESET(sc); /* * If the packet had an error, drop it. Note we * count the error later in the periodic stats update. */ if (status & (RFD_RxFIFOOverrun | RFD_RxRuntFrame | RFD_RxAlignmentError | RFD_RxFCSError | RFD_RxLengthError)) { m_freem(m); continue; } /* * No errors. * * Note we have configured the chip to not include * the CRC at the end of the packet. */ len = RFD_RxDMAFrameLen(status); tailm->m_len = len - sc->sc_rxlen; /* * If the packet is small enough to fit in a * single header mbuf, allocate one and copy * the data into it. This greatly reduces * memory consumption when we receive lots * of small packets. */ if (stge_copy_small != 0 && len <= (MHLEN - 2)) { struct mbuf *nm; MGETHDR(nm, M_DONTWAIT, MT_DATA); if (nm == NULL) { ifp->if_ierrors++; m_freem(m); continue; } nm->m_data += 2; nm->m_pkthdr.len = nm->m_len = len; m_copydata(m, 0, len, mtod(nm, void *)); m_freem(m); m = nm; } /* * Set the incoming checksum information for the packet. */ if (status & RFD_IPDetected) { STGE_EVCNT_INCR(&sc->sc_ev_rxipsum); m->m_pkthdr.csum_flags |= M_CSUM_IPv4; if (status & RFD_IPError) m->m_pkthdr.csum_flags |= M_CSUM_IPv4_BAD; if (status & RFD_TCPDetected) { STGE_EVCNT_INCR(&sc->sc_ev_rxtcpsum); m->m_pkthdr.csum_flags |= M_CSUM_TCPv4; if (status & RFD_TCPError) m->m_pkthdr.csum_flags |= M_CSUM_TCP_UDP_BAD; } else if (status & RFD_UDPDetected) { STGE_EVCNT_INCR(&sc->sc_ev_rxudpsum); m->m_pkthdr.csum_flags |= M_CSUM_UDPv4; if (status & RFD_UDPError) m->m_pkthdr.csum_flags |= M_CSUM_TCP_UDP_BAD; } } m_set_rcvif(m, ifp); m->m_pkthdr.len = len; /* * Pass this up to any BPF listeners, but only * pass if up the stack if it's for us. */ #ifdef STGE_VLAN_UNTAG /* * Check for VLAN tagged packets */ if (status & RFD_VLANDetected) vlan_set_tag(m, RFD_TCI(status)); #endif #if 0 if (status & RFD_VLANDetected) { struct ether_header *eh; u_int16_t etype; eh = mtod(m, struct ether_header *); etype = ntohs(eh->ether_type); printf("%s: VLANtag detected (TCI %d) etype %x\n", ifp->if_xname, (u_int16_t) RFD_TCI(status), etype); } #endif /* Pass it on. */ if_percpuq_enqueue(ifp->if_percpuq, m); } /* Update the receive pointer. */ sc->sc_rxptr = i; } /* * stge_tick: * * One second timer, used to tick the MII. */ static void stge_tick(void *arg) { struct stge_softc *sc = arg; int s; s = splnet(); mii_tick(&sc->sc_mii); stge_stats_update(sc); splx(s); callout_reset(&sc->sc_tick_ch, hz, stge_tick, sc); } /* * stge_stats_update: * * Read the TC9021 statistics counters. */ static void stge_stats_update(struct stge_softc *sc) { struct ifnet *ifp = &sc->sc_ethercom.ec_if; bus_space_tag_t st = sc->sc_st; bus_space_handle_t sh = sc->sc_sh; (void) bus_space_read_4(st, sh, STGE_OctetRcvOk); (void) bus_space_read_4(st, sh, STGE_FramesRcvdOk); ifp->if_ierrors += (u_int) bus_space_read_2(st, sh, STGE_FramesLostRxErrors); (void) bus_space_read_4(st, sh, STGE_OctetXmtdOk); ifp->if_opackets += bus_space_read_4(st, sh, STGE_FramesXmtdOk); ifp->if_collisions += bus_space_read_4(st, sh, STGE_LateCollisions) + bus_space_read_4(st, sh, STGE_MultiColFrames) + bus_space_read_4(st, sh, STGE_SingleColFrames); ifp->if_oerrors += (u_int) bus_space_read_2(st, sh, STGE_FramesAbortXSColls) + (u_int) bus_space_read_2(st, sh, STGE_FramesWEXDeferal); } /* * stge_reset: * * Perform a soft reset on the TC9021. */ static void stge_reset(struct stge_softc *sc) { uint32_t ac; int i; ac = bus_space_read_4(sc->sc_st, sc->sc_sh, STGE_AsicCtrl); /* * Only assert RstOut if we're fiber. We need GMII clocks * to be present in order for the reset to complete on fiber * cards. */ bus_space_write_4(sc->sc_st, sc->sc_sh, STGE_AsicCtrl, ac | AC_GlobalReset | AC_RxReset | AC_TxReset | AC_DMA | AC_FIFO | AC_Network | AC_Host | AC_AutoInit | (sc->sc_usefiber ? AC_RstOut : 0)); delay(50000); for (i = 0; i < STGE_TIMEOUT; i++) { delay(5000); if ((bus_space_read_4(sc->sc_st, sc->sc_sh, STGE_AsicCtrl) & AC_ResetBusy) == 0) break; } if (i == STGE_TIMEOUT) printf("%s: reset failed to complete\n", device_xname(sc->sc_dev)); delay(1000); } /* * stge_init: [ ifnet interface function ] * * Initialize the interface. Must be called at splnet(). */ static int stge_init(struct ifnet *ifp) { struct stge_softc *sc = ifp->if_softc; bus_space_tag_t st = sc->sc_st; bus_space_handle_t sh = sc->sc_sh; struct stge_descsoft *ds; int i, error = 0; /* * Cancel any pending I/O. */ stge_stop(ifp, 0); /* * Reset the chip to a known state. */ stge_reset(sc); /* * Initialize the transmit descriptor ring. */ memset(sc->sc_txdescs, 0, sizeof(sc->sc_txdescs)); for (i = 0; i < STGE_NTXDESC; i++) { sc->sc_txdescs[i].tfd_next = htole64( STGE_CDTXADDR(sc, STGE_NEXTTX(i))); sc->sc_txdescs[i].tfd_control = htole64(TFD_TFDDone); } sc->sc_txpending = 0; sc->sc_txdirty = 0; sc->sc_txlast = STGE_NTXDESC - 1; /* * Initialize the receive descriptor and receive job * descriptor rings. */ for (i = 0; i < STGE_NRXDESC; i++) { ds = &sc->sc_rxsoft[i]; if (ds->ds_mbuf == NULL) { if ((error = stge_add_rxbuf(sc, i)) != 0) { printf("%s: unable to allocate or map rx " "buffer %d, error = %d\n", device_xname(sc->sc_dev), i, error); /* * XXX Should attempt to run with fewer receive * XXX buffers instead of just failing. */ stge_rxdrain(sc); goto out; } } else STGE_INIT_RXDESC(sc, i); } sc->sc_rxptr = 0; sc->sc_rxdiscard = 0; STGE_RXCHAIN_RESET(sc); /* Set the station address. */ for (i = 0; i < 6; i++) bus_space_write_1(st, sh, STGE_StationAddress0 + i, CLLADDR(ifp->if_sadl)[i]); /* * Set the statistics masks. Disable all the RMON stats, * and disable selected stats in the non-RMON stats registers. */ bus_space_write_4(st, sh, STGE_RMONStatisticsMask, 0xffffffff); bus_space_write_4(st, sh, STGE_StatisticsMask, (1U << 1) | (1U << 2) | (1U << 3) | (1U << 4) | (1U << 5) | (1U << 6) | (1U << 7) | (1U << 8) | (1U << 9) | (1U << 10) | (1U << 13) | (1U << 14) | (1U << 15) | (1U << 19) | (1U << 20) | (1U << 21)); /* Set up the receive filter. */ stge_set_filter(sc); /* * Give the transmit and receive ring to the chip. */ bus_space_write_4(st, sh, STGE_TFDListPtrHi, 0); /* NOTE: 32-bit DMA */ bus_space_write_4(st, sh, STGE_TFDListPtrLo, STGE_CDTXADDR(sc, sc->sc_txdirty)); bus_space_write_4(st, sh, STGE_RFDListPtrHi, 0); /* NOTE: 32-bit DMA */ bus_space_write_4(st, sh, STGE_RFDListPtrLo, STGE_CDRXADDR(sc, sc->sc_rxptr)); /* * Initialize the Tx auto-poll period. It's OK to make this number * large (255 is the max, but we use 127) -- we explicitly kick the * transmit engine when there's actually a packet. */ bus_space_write_1(st, sh, STGE_TxDMAPollPeriod, 127); /* ..and the Rx auto-poll period. */ bus_space_write_1(st, sh, STGE_RxDMAPollPeriod, 64); /* Initialize the Tx start threshold. */ bus_space_write_2(st, sh, STGE_TxStartThresh, sc->sc_txthresh); /* RX DMA thresholds, from linux */ bus_space_write_1(st, sh, STGE_RxDMABurstThresh, 0x30); bus_space_write_1(st, sh, STGE_RxDMAUrgentThresh, 0x30); /* * Initialize the Rx DMA interrupt control register. We * request an interrupt after every incoming packet, but * defer it for 32us (64 * 512 ns). When the number of * interrupts pending reaches 8, we stop deferring the * interrupt, and signal it immediately. */ bus_space_write_4(st, sh, STGE_RxDMAIntCtrl, RDIC_RxFrameCount(8) | RDIC_RxDMAWaitTime(512)); /* * Initialize the interrupt mask. */ sc->sc_IntEnable = IS_HostError | IS_TxComplete | IS_UpdateStats | IS_TxDMAComplete | IS_RxDMAComplete | IS_RFDListEnd; bus_space_write_2(st, sh, STGE_IntStatus, 0xffff); bus_space_write_2(st, sh, STGE_IntEnable, sc->sc_IntEnable); /* * Configure the DMA engine. * XXX Should auto-tune TxBurstLimit. */ bus_space_write_4(st, sh, STGE_DMACtrl, sc->sc_DMACtrl | DMAC_TxBurstLimit(3)); /* * Send a PAUSE frame when we reach 29,696 bytes in the Rx * FIFO, and send an un-PAUSE frame when the FIFO is totally * empty again. */ bus_space_write_2(st, sh, STGE_FlowOnTresh, 29696 / 16); bus_space_write_2(st, sh, STGE_FlowOffThresh, 0); /* * Set the maximum frame size. */ bus_space_write_2(st, sh, STGE_MaxFrameSize, ifp->if_mtu + ETHER_HDR_LEN + ETHER_CRC_LEN + ((sc->sc_ethercom.ec_capenable & ETHERCAP_VLAN_MTU) ? ETHER_VLAN_ENCAP_LEN : 0)); /* * Initialize MacCtrl -- do it before setting the media, * as setting the media will actually program the register. * * Note: We have to poke the IFS value before poking * anything else. */ sc->sc_MACCtrl = MC_IFSSelect(0); bus_space_write_4(st, sh, STGE_MACCtrl, sc->sc_MACCtrl); sc->sc_MACCtrl |= MC_StatisticsEnable | MC_TxEnable | MC_RxEnable; #ifdef STGE_VLAN_UNTAG sc->sc_MACCtrl |= MC_AutoVLANuntagging; #endif if (sc->sc_rev >= 6) { /* >= B.2 */ /* Multi-frag frame bug work-around. */ bus_space_write_2(st, sh, STGE_DebugCtrl, bus_space_read_2(st, sh, STGE_DebugCtrl) | 0x0200); /* Tx Poll Now bug work-around. */ bus_space_write_2(st, sh, STGE_DebugCtrl, bus_space_read_2(st, sh, STGE_DebugCtrl) | 0x0010); /* XXX ? from linux */ bus_space_write_2(st, sh, STGE_DebugCtrl, bus_space_read_2(st, sh, STGE_DebugCtrl) | 0x0020); } /* * Set the current media. */ if ((error = ether_mediachange(ifp)) != 0) goto out; /* * Start the one second MII clock. */ callout_reset(&sc->sc_tick_ch, hz, stge_tick, sc); /* * ...all done! */ ifp->if_flags |= IFF_RUNNING; ifp->if_flags &= ~IFF_OACTIVE; out: if (error) printf("%s: interface not running\n", device_xname(sc->sc_dev)); return (error); } /* * stge_drain: * * Drain the receive queue. */ static void stge_rxdrain(struct stge_softc *sc) { struct stge_descsoft *ds; int i; for (i = 0; i < STGE_NRXDESC; i++) { ds = &sc->sc_rxsoft[i]; if (ds->ds_mbuf != NULL) { bus_dmamap_unload(sc->sc_dmat, ds->ds_dmamap); ds->ds_mbuf->m_next = NULL; m_freem(ds->ds_mbuf); ds->ds_mbuf = NULL; } } } /* * stge_stop: [ ifnet interface function ] * * Stop transmission on the interface. */ static void stge_stop(struct ifnet *ifp, int disable) { struct stge_softc *sc = ifp->if_softc; struct stge_descsoft *ds; int i; /* * Stop the one second clock. */ callout_stop(&sc->sc_tick_ch); /* Down the MII. */ mii_down(&sc->sc_mii); /* * Disable interrupts. */ bus_space_write_2(sc->sc_st, sc->sc_sh, STGE_IntEnable, 0); /* * Stop receiver, transmitter, and stats update. */ bus_space_write_4(sc->sc_st, sc->sc_sh, STGE_MACCtrl, MC_StatisticsDisable | MC_TxDisable | MC_RxDisable); /* * Stop the transmit and receive DMA. */ stge_dma_wait(sc); bus_space_write_4(sc->sc_st, sc->sc_sh, STGE_TFDListPtrHi, 0); bus_space_write_4(sc->sc_st, sc->sc_sh, STGE_TFDListPtrLo, 0); bus_space_write_4(sc->sc_st, sc->sc_sh, STGE_RFDListPtrHi, 0); bus_space_write_4(sc->sc_st, sc->sc_sh, STGE_RFDListPtrLo, 0); /* * Release any queued transmit buffers. */ for (i = 0; i < STGE_NTXDESC; i++) { ds = &sc->sc_txsoft[i]; if (ds->ds_mbuf != NULL) { bus_dmamap_unload(sc->sc_dmat, ds->ds_dmamap); m_freem(ds->ds_mbuf); ds->ds_mbuf = NULL; } } /* * Mark the interface down and cancel the watchdog timer. */ ifp->if_flags &= ~(IFF_RUNNING | IFF_OACTIVE); ifp->if_timer = 0; if (disable) stge_rxdrain(sc); } static int stge_eeprom_wait(struct stge_softc *sc) { int i; for (i = 0; i < STGE_TIMEOUT; i++) { delay(1000); if ((bus_space_read_2(sc->sc_st, sc->sc_sh, STGE_EepromCtrl) & EC_EepromBusy) == 0) return (0); } return (1); } /* * stge_read_eeprom: * * Read data from the serial EEPROM. */ static void stge_read_eeprom(struct stge_softc *sc, int offset, uint16_t *data) { if (stge_eeprom_wait(sc)) printf("%s: EEPROM failed to come ready\n", device_xname(sc->sc_dev)); bus_space_write_2(sc->sc_st, sc->sc_sh, STGE_EepromCtrl, EC_EepromAddress(offset) | EC_EepromOpcode(EC_OP_RR)); if (stge_eeprom_wait(sc)) printf("%s: EEPROM read timed out\n", device_xname(sc->sc_dev)); *data = bus_space_read_2(sc->sc_st, sc->sc_sh, STGE_EepromData); } /* * stge_add_rxbuf: * * Add a receive buffer to the indicated descriptor. */ static int stge_add_rxbuf(struct stge_softc *sc, int idx) { struct stge_descsoft *ds = &sc->sc_rxsoft[idx]; struct mbuf *m; int error; MGETHDR(m, M_DONTWAIT, MT_DATA); if (m == NULL) return (ENOBUFS); MCLGET(m, M_DONTWAIT); if ((m->m_flags & M_EXT) == 0) { m_freem(m); return (ENOBUFS); } m->m_data = m->m_ext.ext_buf + 2; m->m_len = MCLBYTES - 2; if (ds->ds_mbuf != NULL) bus_dmamap_unload(sc->sc_dmat, ds->ds_dmamap); ds->ds_mbuf = m; error = bus_dmamap_load(sc->sc_dmat, ds->ds_dmamap, m->m_ext.ext_buf, m->m_ext.ext_size, NULL, BUS_DMA_NOWAIT); if (error) { printf("%s: can't load rx DMA map %d, error = %d\n", device_xname(sc->sc_dev), idx, error); panic("stge_add_rxbuf"); /* XXX */ } bus_dmamap_sync(sc->sc_dmat, ds->ds_dmamap, 0, ds->ds_dmamap->dm_mapsize, BUS_DMASYNC_PREREAD); STGE_INIT_RXDESC(sc, idx); return (0); } /* * stge_set_filter: * * Set up the receive filter. */ static void stge_set_filter(struct stge_softc *sc) { struct ethercom *ec = &sc->sc_ethercom; struct ifnet *ifp = &sc->sc_ethercom.ec_if; struct ether_multi *enm; struct ether_multistep step; uint32_t crc; uint32_t mchash[2]; sc->sc_ReceiveMode = RM_ReceiveUnicast; if (ifp->if_flags & IFF_BROADCAST) sc->sc_ReceiveMode |= RM_ReceiveBroadcast; /* XXX: ST1023 only works in promiscuous mode */ if (sc->sc_stge1023) ifp->if_flags |= IFF_PROMISC; if (ifp->if_flags & IFF_PROMISC) { sc->sc_ReceiveMode |= RM_ReceiveAllFrames; goto allmulti; } /* * Set up the multicast address filter by passing all multicast * addresses through a CRC generator, and then using the low-order * 6 bits as an index into the 64 bit multicast hash table. The * high order bits select the register, while the rest of the bits * select the bit within the register. */ memset(mchash, 0, sizeof(mchash)); ETHER_FIRST_MULTI(step, ec, enm); if (enm == NULL) goto done; while (enm != NULL) { if (memcmp(enm->enm_addrlo, enm->enm_addrhi, ETHER_ADDR_LEN)) { /* * We must listen to a range of multicast addresses. * For now, just accept all multicasts, rather than * trying to set only those filter bits needed to match * the range. (At this time, the only use of address * ranges is for IP multicast routing, for which the * range is big enough to require all bits set.) */ goto allmulti; } crc = ether_crc32_be(enm->enm_addrlo, ETHER_ADDR_LEN); /* Just want the 6 least significant bits. */ crc &= 0x3f; /* Set the corresponding bit in the hash table. */ mchash[crc >> 5] |= 1 << (crc & 0x1f); ETHER_NEXT_MULTI(step, enm); } sc->sc_ReceiveMode |= RM_ReceiveMulticastHash; ifp->if_flags &= ~IFF_ALLMULTI; goto done; allmulti: ifp->if_flags |= IFF_ALLMULTI; sc->sc_ReceiveMode |= RM_ReceiveMulticast; done: if ((ifp->if_flags & IFF_ALLMULTI) == 0) { /* * Program the multicast hash table. */ bus_space_write_4(sc->sc_st, sc->sc_sh, STGE_HashTable0, mchash[0]); bus_space_write_4(sc->sc_st, sc->sc_sh, STGE_HashTable1, mchash[1]); } bus_space_write_2(sc->sc_st, sc->sc_sh, STGE_ReceiveMode, sc->sc_ReceiveMode); } /* * stge_mii_readreg: [mii interface function] * * Read a PHY register on the MII of the TC9021. */ static int stge_mii_readreg(device_t self, int phy, int reg) { return (mii_bitbang_readreg(self, &stge_mii_bitbang_ops, phy, reg)); } /* * stge_mii_writereg: [mii interface function] * * Write a PHY register on the MII of the TC9021. */ static void stge_mii_writereg(device_t self, int phy, int reg, int val) { mii_bitbang_writereg(self, &stge_mii_bitbang_ops, phy, reg, val); } /* * stge_mii_statchg: [mii interface function] * * Callback from MII layer when media changes. */ static void stge_mii_statchg(struct ifnet *ifp) { struct stge_softc *sc = ifp->if_softc; if (sc->sc_mii.mii_media_active & IFM_FDX) sc->sc_MACCtrl |= MC_DuplexSelect; else sc->sc_MACCtrl &= ~MC_DuplexSelect; /* XXX 802.1x flow-control? */ bus_space_write_4(sc->sc_st, sc->sc_sh, STGE_MACCtrl, sc->sc_MACCtrl); } /* * sste_mii_bitbang_read: [mii bit-bang interface function] * * Read the MII serial port for the MII bit-bang module. */ static uint32_t stge_mii_bitbang_read(device_t self) { struct stge_softc *sc = device_private(self); return (bus_space_read_1(sc->sc_st, sc->sc_sh, STGE_PhyCtrl)); } /* * stge_mii_bitbang_write: [mii big-bang interface function] * * Write the MII serial port for the MII bit-bang module. */ static void stge_mii_bitbang_write(device_t self, uint32_t val) { struct stge_softc *sc = device_private(self); bus_space_write_1(sc->sc_st, sc->sc_sh, STGE_PhyCtrl, val | sc->sc_PhyCtrl); }